12.2 DELAY
12. FX AND MIXER PARAMETERS > 12.2 DELAY · PDF p. 61–62 · OS 1.15A
# 12.2 DELAY 12. FX AND MIXER PARAMETERS 12. FX AND MIXER PARAMETERS The Digitakt II effects and mixers parameters are explained in this chapter. 12.1 EDITING THE SEND FX AND MIXER PARAMETERS The Digitakt II’s Chorus, Delay and Reverb are send effects and are set on a pattern level. It means that all the presets in a pattern shares the same effect settings but have individual send levels to the effects. The Delay, Reverb, and Chorus parameters are set on their respective PARAMETER page, but their incoming signals are set by the DEL, REV, and CHO send parameters on the FX page of each audio track. Press [FUNC] + [FX] to access the SEND FX parameter pages, and then use the [UP]/[DOWN] keys to navigate between the sub pages. Use the DATA ENTRY knobs A-H to change the parameters. Press [FUNC] + [MOD] to access the MIXER parameter pages, and then use the [UP]/[DOWN] keys to navigate between the sub pages. Use the DATA ENTRY knobs A-H to change the parameters. The FX and MIXER parameter settings are stored as part of the pattern. Don’t forget to save the pattern and give it a unique name once you have achieved the results you want. 12.2 DELAY (SEND FX PAGE 1) The Delay send effect takes the input signal, delays it in time and then rejoins it with the original signal. TIME Delay Time sets the delay time. It is relative to the current BPM and is measured in 128th notes. TIME setting Divide ratio 1/128 1/64 2.67 1/48 (1/32T) 1/64. 1/32 5.33 1/24 (1/16T) 1/32. 1/16 10.67 1/12 (1/8T) 1/16. 1/8 21.33 1/6 (1/4T) 1/8. 1/4 42.67 1/3 (1/2T) 1/4. 1/2 1/2. 12. FX AND MIXER PARAMETERS X Ping-pong sets the delay signal to alternate across the stereo field. There are two settings: • OFF lets you manually set the position of the delay signal in the stereo field. Use the WID parameter to change the stereo field position. • ON makes the delay signal alternate between left and right pan positions. The WID parameter controls the amount of panning. WID Stereo Width sets the delay signal pan width across the stereo field. The knob is bipolar. FDBK Feedback Gain sets the amount of delay output signal to feed back into the input of the delay. With high er parameter settings, infinite and/or swelling delays are possible. Please be aware that high feedback can lead to a very loud signal. VOL Delay Volume sets the volume of the Delay output signal. Use LEVEL/DATA to set this parameter. HPF HPF sets the cutoff frequency of the delay highpass filter. LPF LPF sets the cutoff frequency of the delay lowpass filter. REV Reverb Send sets the amount of Delay output signal to be sent to the Reverb. 12.3 REVERB (SEND FX PAGE 2) The Reverb send effect controls the persistence, and ambient characteristics, of the sound reverberations. It can simulate many different sonic locations, from huge spaces to small rooms. PRE Pre-delay sets the pre-delay time of the Reverb. DEC Decay Time sets the length of the decay phase of the reverberated signal, essentially setting the size of the acoustic space. FREQ FB Shelving Freq sets the shelving filter frequency. Together with the GAIN parameter, it can be used to dampen the reverberated signal above a chosen frequency, making the reverberation sound more promi nent or more muffled. GAIN FB Shelving Gain affects the damping of the reverberated signal above the shelving frequency set by the FREQ parameter. At max value the treble is included in the reverberations; lowering the value gradually dampens it. VOL Reverb Volume sets the volume of the Reverb output signal. Use LEVEL/DATA to set this parameter.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.