14.3 PATTERN MENU
14. SETTINGS MENU > 14.3 PATTERN MENU · PDF p. 76–77 · OS 1.15A
# 14.3 PATTERN MENU 14. SETTINGS MENU 14.2 SONG In this menu, you can perform tasks related to songs. For more information, please see “10.9 SONG MODE” on page 50. 14.2.1 RENAME Opens the NAMING screen where you can rename the active song. 14.2.2 CLEAR Clears the active song. 14.2.3 LOAD Opens a screen where you can select and load songs 14.2.4 SAVE TO PROJ Saves the active song to the project. 14.3 PATTERN MENU Use the PATTERN menu to perform pattern management. Use the [UP] and [DOWN] arrow keys to move between the options. Press [YES] to confirm your selection. Press [NO] to exit the menu. 14.3.1 RENAME Opens the NAMING screen where you can rename the active pattern. 14.3.2 CLEAR • WHOLE PATTERN Clears the active pattern’s sequencer data and kit. A prompt appears when you select this option. Press [YES] to clear, or [NO] to cancel the operation. Note that no pattern informa tion will be permanently lost until the pattern is saved to the same pattern slot that it was loaded from. • KIT DATA Clears the active pattern’s kit. All sequencer data will remain unchanged. A prompt ap pears when you select this option. Press [YES] to clear, or [NO] to cancel the operation. Note that no kit information will be permanently lost until the pattern is saved to the same pattern slot that it was loaded from. • SEQUENCE DATA Clears the active pattern’s sequence data. All presets will remain unchanged. A prompt appears when you select this option. Press [YES] to clear, or [NO] to cancel the operation. Note that no sequencer information are permanently lost until the pattern is saved to the same pattern slot it was loaded from. 14.3.3 SAVE TO PROJ You must have saved the project at least once before you can save pattern information. • WHOLE PATTERN Saves the active pattern’s sequence data and kit to the +Drive. A prompt appears when you select this option. Press [YES] to save, or [NO] to cancel the operation. • KIT DATA Saves the active pattern’s kit to the +Drive. A prompt appears when you select this option. Press [YES] to save, or [NO] to cancel the operation. 14. SETTINGS MENU • SEQUENCE DATA Saves the active pattern’s sequence data to the +Drive. A prompt appears when you select this option. Press [YES] to save, or [NO] to cancel the operation. 14.3.4 RELOAD FROM PROJ You must have saved the pattern at least once before you can reload pattern information. • WHOLE PATTERN Reloads the active pattern’s sequence data and kit from the +Drive. A prompt will appear when you select this option. Press [YES] to reload, or [NO] to cancel the operation. • KIT DATA Reloads the active pattern’s kit from the +Drive. A prompt appears when you select this option. Press [YES] to reload, or [NO] to cancel the operation. • SEQUENCE DATA Reloads the active pattern’s all sequence data from the +Drive. A prompt appears when you select this option. Press [YES] to reload, or [NO] to cancel the operation. 14.4 MIDI CONFIG In this menu, various sub-menus dealing with the MIDI functionality of Digitakt II are found. 14.4.1 SYNC Controls how Digitakt II receives and sends MIDI clock and transport commands. Change settings by using the [LEFT]/[RIGHT] arrow keys or the [YES] key. CLOCK RECEIVE sets whether or not Digitakt II responds to MIDI clock sent from external devices. CLOCK SEND sets whether or not Digitakt II transmits MIDI clock. TRANSPORT RECEIVE sets whether or not Digitakt II responds to MIDI transport messages sent from external devices. TRANSPORT SEND sets whether or not Digitakt II transmits MIDI transport messages. PRG CH RECEIVE will, when active, make Digitakt II respond to incoming program change messages, which is useful when wanting to select patterns externally. The MIDI channel that will listen to incom ing program change messages is set in the MIDI CHANNELS menu. For more information, please see “14.4.3 CHANNELS” on page 79. PRG CH SEND will, when active, send program change messages when patterns are changed. The MIDI channel that will send program change messages is set in the MIDI CHANNELS menu. For more information, please see “14.4.3 CHANNELS” on page 79. 14.4.2 PORT CONFIG Here you find the MIDI port related settings. Change settings by using the [LEFT]/[RIGHT] arrow keys.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.