← Search

11.8 FX PAGE

11. TRACK PARAMETERS > 11.8 FX PAGE · PDF p. 62–63 · OS 1.10D

# 11.8 FX PAGE

11. TRACK PARAMETERS
Amplitude envelope with MODE set to AHD and HOLD set to NOTE.
TIME
AMPLITUDE
Note On
Attack
Decay
Hold
Note Off
Attack
Decay
Hold
Note
On
Note Off
Attack/
Hold
Decay
Note On
Note Off
11.8 FX PAGE
The FX parameter page contains a number of FX related parameters such as the Bit Reduction, Overdrive,
and Sample Rate Reduction. Here you also find the send levels for the Delay, Reverb, and Chorus effects.
Press [FX] to access this parameter page.
BR
Bit Reduction sets the bit depth. The parameter range is from 16 bits to 1 bit.
OVER
Overdrive sets the gain amount into the digital overdrive.
SRR
Sample Rate Reduction sets the amount of sample rate reduction.
SR.RT
SRR Routing sets if the Sample Rate Reduction effect is routed before (PRE) or after (POST) the filter
machine.
DEL
Delay Send sets the amount of sound sent through to the Delay effect. For more information, please see
“12. FX AND MIXER PARAMETERS” on page 65.
REV
Reverb Send sets the amount of sound sent through to the Reverb effect. For more information, please
see “12. FX AND MIXER PARAMETERS” on page 65.
CHR
Chorus Send sets the amount of sound sent through to the Chorus effect. For more information, please
see “12. FX AND MIXER PARAMETERS” on page 65.
OD.RT
Overdrive Routing selects if the overdrive effect is routed before (PRE) or after (POST) the filter machine.
Please note that there are no parameters on the FX page for MIDI tracks.

11. TRACK PARAMETERS
11.9 MOD PAGE 1
The MOD pages contain three LFOs (two for tracks that use MIDI machines). The Low-Frequency Oscilla­
tor can be used to modulate track parameters. Customize the low-frequency oscillator behavior, orientation,
speed, and depth on this page. This page controls the behavior of LFO 1
Press [MOD] to access this parameter page.
SPD
Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The knob
is bipolar. The LFO cycle can be played backward by using negative values.
MULT
Multiplier multiplies the SPD parameter by the set factor either by multiplying the current tempo (BPM
settings), or by multiplying a fixed tempo of 120 BPM.
FADE
Fade In/Out makes it possible to fade in/fade out the LFO modulation. The knob is bipolar. Positive val­
ues give a fade-out, negative values give a fade in. 0 gives no fade in/fade out. (-64–63)
DEST
Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect
the sound by highlighting a destination. Press [YES] to confirm the selection. Press [NO] to cancel and
revert to previous selection. Press [FUNC] and then turn the knob to snap to destination sections. For
more information, please see “APPENDIX D: MODULATION DESTINATIONS” on page 118
WAVE
Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are
bipolar. The Exponential and Ramp are unipolar.
SPH
Start Phase sets the point within the wave cycle where the LFO will start when it is trigged. 0 makes the
LFO start at the beginning of a complete wave cycle, 64 makes it start at the center. A small square at
the start of the waveform shows that the wave cycle starts at a zero-crossing. If WAV is set to RND then
the SPH parameter changes to SLEW and adds slew to the transitions in the waveform.
MODE
Trig Mode sets how the LFO will act when a note is trigged.
• FREE is the default free-running mode. It makes the LFO run continuously, never restarting or
stopping even if notes are trigged.
• TRIG makes the LFO restart when a note is trigged.
• HOLD makes the LFO run free in the background, but when a note is trigged the LFO output level is
latched and held still until the next note is trigged.
• ONE The LFO starts when a note is trigged, then runs to the end of the waveform and then stops.
This makes the LFO function similar to an envelope.
• HALF The LFO starts when a note is trigged, then runs to the middle of the waveform and then stops.
DEP
Depth sets the depth and polarity of the LFO modulation. Both negative and positive modulation depth is
possible. A center setting, 0.00, equals no modulation depth.
11.10 MOD PAGE 2
MOD page 2 page contains the same parameters as LFO page 1, but controls the behavior of LFO 2.

Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.