13.7 PERSONALIZE
13. SETTINGS MENU > 13.7 PERSONALIZE · PDF p. 78–80 · OS 1.10D
# 13.7 PERSONALIZE 13. SETTINGS MENU 13.6.3 USB IN Sets where the incoming audio from the class compliant device is routed to in the Digitone II’s signal path. This parameter is only available when USB CONFIG is set to USB AUDIO/MIDI. For more informa tion, please see “13.8.1 USB CONFIG” on page 80. MAIN The incoming audio is routed to the Digitone II’s main outputs. OFF No sound is routed from USB to the Digitone II. 13.6.4 USB OUT Sets from where in the Digitone II’s signal path, the outgoing audio is routed to the class compliant device. This parameter is only available when USB CONFIG is set to USB AUDIO/MIDI. For more informa tion, please see “13.8.1 USB CONFIG” on page 80. MAIN The outgoing audio is routed from the Digitone II’s Main out at the end of the signal path. L:T1–16/R:T1–16 The outgoing audio is routed from the selected track(s) Press a [TRIG] key twice to select a single track as a stereo source. The selected track’s [TRIG] key lights up white. Press first one [TRIG] key and then another to select two separate tracks as sources. The selected tracks’ [TRIG] keys lights up blue for left channel and red for right channel. The audio from each track is then summed to mono, routed out and sent separately on left and right channel. EXT The outgoing audio is routed straight from the Digitone II’s audio inputs IN L/R to the class com pliant device. OFF No audio is sent to the class compliant device. 13.6.5 INT TO MAIN Sets if Digitone II sends internal audio to the MAIN OUT and HEADPHONES OUT or not when used with a class compliant audio device. OFF No sound is sent to main out. ON Sound is always sent to main out. 13.6.6 USB TO MAIN [dB] Sets the amount of amplification of the sound that is streamed over USB to the Digitone II main out when used with a class compliant audio device. (0 dB–+18 dB) 13.6.7 PRE/POST FADER Sets if audio over USB should be pre or post the track level setting. Audio from the TRACK OUTPUTS is always without any effects. 13.7 PERSONALIZE Here you can customize a number of settings to fit you personal preferences. 13.7.1 LED INTENSITY Sets the brightness of the key LEDs and screen. Use the [LEFT]/[RIGHT] keys to change the setting. 13.7.2 LED BACKLIGHT Switches the key LEDs backlight on/off. Press and hold [SETTINGS] for a second and then press [TRIG 1–3] to set the intensity of the key LEDs and screen. Press and hold [SETTINGS] for a second and then press [TRIG 9] to toggle the key LEDs backlight on/off. 13. SETTINGS MENU 13.7.3 REMEMBER SUBPAGE Will, when selected, remember which PARAMETER page’s subpage you last used and access this page again the next time you press the same [PARAMETER] key. Use the [YES] key to toggle this setting. (ON, OFF). 13.7.4 U/D KEY MODE Sets the functionality of the [UP]/[DOWN] keys. When set to KB OCT and you are in KEYBOARD mode, the keys shift keyboard octave up/down. When you are not in KEYBOARD mode, then keys navigates between parameter group pages. When set to NAV, the keys only navigate between parameter pages. 13.7.5 PAGE AUTOCOPY Will, when set to on, automatically copy already placed trigs when extending the length of a pattern. If a pattern consists of for example two pages and the pattern length is increased to four pages, the two additional pattern pages are then copies of the first two pattern pages. For more information, please see “10.11 PAGE SETUP MENU” on page 48. 13.7.6 NOTE PARAM Sets the interaction behavior for the NOTE parameter on the TRIG PARAMETERS page. CHRO: Turning DATA ENTRY knob A changes the parameter in chromatic steps. Pressing and turning DATA ENTRY knob A changes the parameter in steps that follows the set scale. SCALE: Turning DATA ENTRY knob A changes the parameter in steps that follows the set scale. Press ing and turning DATA ENTRY knob A changes the parameter in chromatic steps. For more information, please see “8.5.2 KEYBOARD SETUP MENU” on page 25 and “11.2 TRIG PAGE 1” on page 57. 13.7.7 LIVE REC OVERDUB When checked, allow you to add notes and locks in LIVE RECORDING mode to already placed trigs instead of replacing them. 13.7.8 PARAM LIVE REC This option lets you select whether parameter locks recorded in LIVE RECORDING mode will be added to all sequencer steps or only to steps that already contain a trig. 13.7.9 TRK SELECT This option lets you decide what happens when you press a trig key (when not in a recording mode) to change tracks. NORMAL Tracks are selected when pressing a [TRIG] key and plays a sound. SILENT Tracks are selected when pressing a [TRIG] key but does not play a sound. MANUAL Tracks are not selected when pressing a [TRIG] key but plays a sound. INVERTED Tracks are selected when pressing a [TRIG] key but does not play a sound. However [TRK]+[TRIG] plays the track’s sound without selecting the track. In NORMAL, SILENT, and MANUAL, [TRK]+[TRIG] selects the track without playing a sound. 13.7.10 NOTE PREVIEW This option lets you decide if a Note added using the Note editor is played and heard or not. ALWAYS Notes are always played when added PAUSED Notes are only played when the sequencer is paused/stopped (they are not heard when the sequencer is running) NEVER Notes are never played when added. 13.7.11 NOTE EDIT MENU This option lets you decide how you access the NOTE EDIT menu. ANY You can always acces the NOTE EDIT menu by pressing [NOTE EDIT]. REC You need to press [RECORD] and then press [NOTE EDIT] to access the NOTE EDIT menu. This option is useful if you dont want to accidentally open the NOTE EDIT menu when you use the [TRIG] key to manually play notes and beats. 13. SETTINGS MENU 13.8 SYSTEM The System menu contains a number of system related settings for the Digitone II. 13.8.1 USB CONFIG Here you find settings related to USB audio and MIDI. Selecting one mode disables the other two modes. USB MIDI select this option if you wish to send and receive MIDI over USB. USB AUDIO/MIDI sets the Digitone II to send and receive audio and MIDI over USB. Select this option if you want to use the Digitone II together with a class compliant USB audio host. 13.8.2 OS UPGRADE Use this menu option when you want to upgrade the Digitone II OS. To send the OS file, use our free Elektron Transfer software. Elektron Transfer can be downloaded from the Elektron website. The device sending the OS file must be connected to the USB port of Digitone II. Please note that the Digitone II will not appear as an icon on your computer desktop. 1. Download the Digitone II OS file from the Elektron website. 2. Connect the Elektron device to the computer via USB. 3. Open the Transfer application on your computer. 4. On the Transfer CONNECTIONS page, set the MIDI IN and MIDI OUT ports to your Elektron device. 5. On the Transfer DROP page, drag and drop the OS file. The OS file is then automatically trans ferred to the Elektron device and the OS update initiates. A progress bar is visible on device screen when receiving the OS. 6. On your device. Press [YES] to confirm the OS update. When the update is done, the Digitone II will reboot. 13.8.3 FORMAT +DRIVE You have the possibility to erase all content of the +Drive. Once you have made your choice using the [LEFT]/[RIGHT] keys and confirmed by pressing [YES], a prompt will appear asking if you want to exe cute the formatting procedure. Press [YES] to proceed with the formatting. PROJ+PST+KIT Erases all projects, presets, and kits. 13.8.4 MASTER TUNE Sets the master tune for the whole device. Use [LEFT]/[RIGHT] to edit the value.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.