11.4 FLTR PAGE (CC VALUE)

11. MIDI TRACK PARAMETERS > 11.4 FLTR PAGE (CC VALUE) · PDF p. 59–60 · OS 1.40A

# 11.4 FLTR PAGE (CC VALUE)

11. MIDI TRACK PARAMETERS
11.2.6 LFO.T
LFO Trig controls if the LFO will be trigged or not.
11.3 SYN PAGE
Here you can set the MIDI channel that the MIDI track should use to send data. Bank and program change
values are also set here, together with a few standard CC parameters. The default value of the parameters
on this page is OFF, meaning they are disabled and will not send out any data. Press and hold [FUNC] and
then press the DATA ENTRY knobs to enable them. You can then use the DATA ENTRY knobs to set the
parameter values as usual. Disable the parameters by repeating the enabling procedure.
Press [SYN] once to access this parameter page.
11.3.1 CHAN
Channel sets the MIDI channel the track sends MIDI data to. If you set this parameter to OFF, it turns the
MIDI track off. Please note that this parameter cannot be parameter locked.
11.3.2 BANK
Bank sends a bank change message on CC 0 MSB.
11.3.3 SBNK
Sub Bank sends a bank change message on CC 32 LSB.
11.3.4 PROG
Program Change sends a Program Change message.
11.3.5 PB
Pitch Bend controls the pitch bend data sent on the MIDI track.
11.3.6 AT
Aftertouch controls the aftertouch data sent on the MIDI track.
11.3.7 MW
Mod Wheel controls the modulation wheel data sent on the MIDI track.
11.3.8 BC
Breath controller controls the breath control data sent on the MIDI track.
11.4 FLTR PAGE (CC VALUE)
Here you can set the values of up to eight assignable CC commands. The default value of the parameters
on this page is OFF, meaning they are disabled and will not send out any data. Press and hold [FUNC] and
then press the DATA ENTRY knobs to enable them. You can then use the DATA ENTRY knobs to set the
parameter values as usual. Disable the parameters by repeating the enabling procedure.
Press [FLTR] to access this parameter page.

11. MIDI TRACK PARAMETERS
11.4.1 VAL1-VAL8
CC 1–8 Value controls the values that are sent for the CC commands, which are specified on the AMP
(CC SELECT) page. These parameters default value is OFF. Press [TRIG] + DATA ENTRY knobs to acti
vate the parameters and then set a value.
11.5 AMP PAGE (CC SELECT)
Here you select the eight CC commands whose values are controlled by the parameters on the FLTR PAGE
(CC VALUE) page.
Press [AMP] to access this parameter page.
11.5.1 SEL1-SEL8
CC 1–8 Select specifies the CC commands that are controlled by the parameters on the AMP PAGE 1
(CC VALUE) page. The selectable values are the standard MIDI Control Change Messages.
11.6 LFO PAGE
The Low-Frequency Oscillator can be used to interact with the parameters found on the MIDI tracks’ SYN,
and FLTR pages. Customize the low-frequency oscillator behavior, orientation, and depth on this page.
Press [LFO] to access this parameter page.
11.6.1 SPD
Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The pa
rameter is bipolar. The LFO cycle can be played backward by using negative values.
11.6.2 MULT
Multiplier multiplies the SPD parameter by the set factor either by multiplying the current tempo (BPM
settings), or by multiplying a fixed tempo of 120 BPM.
11.6.3 FADE
Fade In/Out makes it possible to fade in/fade out the LFO modulation. The knob is bipolar. Positive val
ues give a fade-out, negative values give a fade in. 0 gives no fade in/fade out.
11.6.4 DEST
Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect
the sound by highlighting a destination. Press [YES] to confirm the selection. For more information,
please see “APPENDIX C: LFO MODULATION DESTINATIONS” on page 119
11.6.5 WAVE
Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are
bipolar. The Exponential and Ramp are unipolar.

Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.