12.3 SYN PARAMETERS PAGE
12. FX TRACK PARAMETERS > 12.3 SYN PARAMETERS PAGE · PDF p. 62–63 · OS 1.40A
# 12.3 SYN PARAMETERS PAGE 12. FX TRACK PARAMETERS 12. FX TRACK PARAMETERS Here follows a description of the parameters that are on the FX track’s PARAMETER pages. The FX track controls the parameters of the Analog FX block and in addition it also gives sequencer control over the parameters on the REVERB and DELAY parameter pages. For more information, please see “13. DELAY, REVERB AND MIXER PARAMETERS” on page 68. The FX track’s parameters are saved together with the pattern. The parameters may be locked to other settings on any step of the pattern by first pressing and holding a [TRIG] key, then changing the parameters settings with the DATA ENTRY knobs. For more infor mation, please see “9.10.1 PARAMETER LOCKS” on page 43. 12.1 EDITING THE FX TRACK PARAMETERS Press the [FX] key to access the FX track and then use the [PARAMETER] keys to access the different PA RAMETER pages. Use the DATA ENTRY knobs A-H to change the parameters. Press and hold a [PARAME TER] key to see the values for all parameters on that page. 12.2 TRIG PARAMETERS PAGE Set the actions for what a trig on the FX does. These general settings affect trigs placed in the sequencer. Use the DATA ENTRY knobs to change the settings. Press [TRIG PARAMETERS] to access this parameter page. 12.2.1 LEN Trig Length sets the length of the trig. In LIVE RECORDING mode, the duration of pressing the [TRIG] keys overrides this general setting. 12.2.2 PROB Trig Probability sets the probability that the trigs on the track plays or not. The probability outcome is re-evaluated every time a trig plays. The default setting is 100%, meaning that all the trigs on the track plays every time. This parameter changes temporarily to display and control COND (Trig Condition) when you add a condi tional lock. COND sets the Trig Condition with which a set of conditional rules can be applied to any trig, using a parameter lock. For more information, please see “9.10.3 TRIG CONDITIONS AND CONDITION AL LOCKS” on page 44. If you have placed a conditional lock on a trig in the sequencer, the trig condition overrides the Trig Probability setting. For example, if you set PROB to 70% and a FILL trig condition on a trig, that trig will only (and always) play when the Syntakt is in FILL mode. 12.2.3 LFO.T LFO Trig controls if the LFO will be trigged or not. 12.2.4 FLT.T Filter Trig controls if the filter envelope will be trigged or not. 12.2.5 AMP.T Amplifier Trig controls if the FX tracks amplifier envelope will be trigged or not. 12.3 SYN PARAMETERS PAGE On this page you can set the set the amount of analog drive on the FX track. For more information, please see “5.4 ANALOG FX BLOCK” on page 17. Press [SYN] to access this parameter page. 12. FX TRACK PARAMETERS 12.3.8 DRIVE Drive sets the amount of analog drive that is added to the audio routed through the FX track. Yes, it goes to 11! 12.4 FLTR PAGE 1 On FILTER page 1, you will find the parameters that control the analog multimode filter and its associated envelope. Press [FLTR] to access this parameter page. 12.4.1 ATK Attack Time sets the length of the attack phase of the filter envelope. 12.4.2 DEC Decay Time sets the length of the decay phase of the filter envelope. 12.4.3 SUS Sustain Level sets the sustain level of the filter envelope. 12.4.4 REL Release Time sets the length of the release phase of the filter envelope. 12.4.5 FREQ Frequency sets the cutoff frequency of the multimode filter. 12.4.6 RESO Resonance sets the resonance behavior of the filter. Resonance introduces a peak in the spectrum at the cutoff frequency. 12.4.7 TYPE Filter Type selects the type of filter. (4-pole Lowpass, 2-pole Lowpass, Bandpass, Highpass, Notch, Dou ble-Notch, Lowpass-Notch, OFF) 12.4.8 ENV Env. Depth sets the amount of cutoff frequency modulation from the filter envelope. The knob is bipolar, both negative and positive modulation depths are available.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.