← Search

12.8 LFO PAGE 1

12. FX TRACK PARAMETERS > 12.8 LFO PAGE 1 · PDF p. 66–67 · OS 1.40A

# 12.8 LFO PAGE 1

12. FX TRACK PARAMETERS
Inverted amplitude envelope with HOLD set to NOTE.
TIME
AMPLITUDE
Note On
Attack
Decay
Hold
Note
Off
Attack
Decay
Hold
Note
On
Note Off
Attack/
Hold
Decay
Note On
Note Off
12.7 AMP PAGE 2
The AMP page 2 controls parameters for the amp envelope reset and the envelope mode.
Press [AMP] to access this parameter page.
12.7.1 AENR
Amp envelope reset sets the amp envelope behavior:
ON resets the envelopes for each consecutive trig (default).
OFF does not reset the envelopes for each consecutive trig.
12.7.2 MODE
Envelope mode sets the amplitude envelope to function as an inverted AHD, an AHD or an ADSR enve­
lope.
12.8 LFO PAGE 1
The Low-Frequency Oscillator can be used to modulate the parameters found on the audio tracks SYN,
FILTER and AMP pages. Customize the low-frequency oscillator behavior, orientation, and depth on this
page. This page controls the behavior of LFO 1
Press [LFO] to access this parameter page.
12.8.1 SPD
Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The knob
is bipolar. The LFO cycle can be played backward by using negative values.

12. FX TRACK PARAMETERS
12.8.2 MULT
Multiplier multiplies the SPD parameter by the set factor either by multiplying the current tempo (BPM
settings), or by multiplying a fixed tempo of 120 BPM.
12.8.3 FADE
Fade In/Out makes it possible to fade in/fade out the LFO modulation. The knob is bipolar. Positive val­
ues give a fade-out, negative values give a fade in. 0 gives no fade in/fade out.
12.8.4 DEST
Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect
the sound by highlighting a destination. Press [YES] to confirm the selection. For more information,
please see “APPENDIX C: LFO MODULATION DESTINATIONS” on page 119
12.8.5 WAVE
Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are
bipolar. The Exponential and Ramp are unipolar.
12.8.6 SPH
Start Phase sets the point within the wave cycle where the LFO will start when it is trigged. 0 makes
the LFO start at the beginning of a complete wave cycle, 64 makes it start at the center. A small square
at the start of the waveform shows that the wave cycle starts at a zero-crossing (not available in FREE
and HOLD mode. If WAV is set to RND then the SPH parameter changes to SLEW and adds slew to the
transitions in the waveform.
12.8.7 MODE
Trig Mode sets how the LFO will act when a note is trigged.
• FREE is the default free-running mode. It makes the LFO run continuously, never restarting or
stopping even if notes are trigged.
• TRIG makes the LFO restart when a note is trigged.
• HOLD makes the LFO run free in the background, but when a note is trigged the LFO output level is
latched and held still until the next note is trigged.
• ONE The LFO starts when a note is trigged, then runs to the end of the waveform and then stops.
This makes the LFO function similar to an envelope.
• HALF The LFO starts when a note is trigged, then runs to the middle of the waveform and then stops.
12.8.8 DEP
Depth sets the depth and polarity of the LFO modulation. Both negative (inverted) and positive modula­
tion depth is possible. A center setting, 0.00, equals no modulation depth. (-64.00–63.00)
12.9 LFO PAGE 2
LFO page 2 page contains the same parameters as LFO page 1, but controls the behavior of LFO 2. Press
[LFO] twice to access this parameter page.

Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.