6.3 PARAMETER EDITING
6. INTERACTING WITH TONVERK > 6.3 PARAMETER EDITING · PDF p. 22–23 · OS 1.3.3
# 6.3 PARAMETER EDITING 6. INTERACTING WITH TONVERK 6. INTERACTING WITH TONVERK The screen shows all the information needed for real-time interaction and editing on Tonverk. The eight DATA ENTRY knob parameters shown will vary depending on the given situation. 1. Bank and pattern. 2. Pattern name. 3. Trig mode. 4. Sequencer page indicator. Squares shows the number of used pages (max 16 pages). An unfilled square shows the currently active page. 5. The tempo. When Tonverk’s tempo is synced to external MIDI, a lock icon appears next to the tempo. 6. Track parameters. They show what the eight DATA ENTRY knobs control and their current parameter values. 7. Parameter page indicator. Indicates the number of pages for the selected parameter section and which page is currently selected. 8. The main level setting of the active track. Use the LEVEL/DATA knob to change the level setting. 9. Active track. 10. Track/Machine type. Tonverk features a screen saver that dims the screen after 5 minutes of inactivity and turns off the screen after 60 minutes. Press any key or move any controller to wake the screen. 6.1 SETTING THE VOLUME MAIN VOLUME sets the volume for the A/B outputs and the E/F (Headphones) outputs. 6.2 SCREEN NAVIGATION Use the [ARROW] keys [UP], [DOWN], [LEFT] or [RIGHT] to navigate menus or sub-menus. The LEVEL/DATA knob can be used to scroll through menus and lists quickly. [YES] is used to confirm, select, enter sub-menus/folders and tick/untick boxes. [NO] is used to cancel, deselect or go back one or more steps in menu and folder structures. 6.3 PARAMETER EDITING The [PARAMETER PAGE] keys open the corresponding parameter page group, where you can edit the tracks. The DATA ENTRY knobs are used to change the values of the track parameters. The positions of the parameters on the screen correspond to the physical locations of the knobs on the front panel. Press and turn a knob to adjust its parameter in larger increments. Use the [UP]/[DOWN] keys to cycle through the parameter group’s pages. You can also press a [PARAMETER PAGE] key repeatedly to cycle through the parameter pages in that group. Press and hold a [PARAMETER PAGE] key to see the values for all parame ters on that page. For more information, please see “12. AUDIO TRACK PARAMETERS” on page 54, and “APPENDIX A: MACHINES” on page 84. • The parameters are adjusted in larger increments if you press down the DATA ENTRY knob while turning it. This makes it quicker to sweep through the whole parameter range. • Press DATA ENTRY knob + [NO] to reset the parameter to the default value. 6. INTERACTING WITH TONVERK • Press [PARAMETER PAGE] key + [PLAY] to reset all the parameters in the selected parameter page to default values. • Press and hold a [PARAMETER PAGE] key to see the values for all parameters on that page. 6.3.1 PARAMETER SNAP VALUES Pressing [FUNC] while editing specific parameters will cause the parameter values to snap to suitable musical and performance related values. The NOTE parameter, for example, snaps to octave steps, and the PAN parameter snaps to full left, center, and full right. 6.4 [FUNC] KEY PRESS COMBINATIONS The standard way to use the [FUNC] key in combination with other keys is to press and hold [FUNC] and then press the second key in the combination. 6.5 QUICK SCROLLING Scroll through menus using the LEVEL/DATA knob. Quick scrolling is possible on many menus. Press [FUNC] + the [UP/DOWN] keys to move the cursor one menu page. 6.6 COPY, CLEAR, AND PASTE Copy, clear, and paste commands are available in many contexts. Pressing [FUNC] + [RECORD] to copy. Press [FUNC] + [STOP] to paste. Press [FUNC] + [PLAY] to clear. Please refer to the various sections in the manual for more information on when these commands are available. For more information, please see “19. KEY COMBINATIONS” on page 79. 6.7 THE NAMING SCREEN The naming method is identical for the various naming situations.. The [LEFT] and [RIGHT] arrow keys are used to navigate between the characters. Turning the LEVEL/ DATA knob or pressing the [UP] or [DOWN] arrow keys selects the characters. [FUNC] + [NO] erases characters. [FUNC] + [YES] inserts a space. Press [SETTINGS] to create a random name. Press and hold [FUNC] to access the Pop-up Naming menu. 6.7.1 POP-UP NAMING A convenient way of naming is to open a pop-up menu that shows all available letters, symbols, and digits. Press and hold the [FUNC] key when you are on the NAMING screen to access the Pop-up naming screen. Keep [FUNC] pressed and use the [ARROW] keys to highlight the character you want to insert. Once there, release [FUNC] to add the character. At the same time, pressing and holding [FUNC], press [TRIG 1 / TRIG 2] to switch between character layouts.
Chunks share pages with neighboring sections; text before/after the section heading belongs to the adjacent sections.