15.8 MOD PAGE 2 (LFO 2)
15. MIX TRACK PARAMETERS > 15.8 MOD PAGE 2 (LFO 2) · PDF p. 70–71 · OS 1.3.3
# 15.8 MOD PAGE 2 (LFO 2) 15. MIX TRACK PARAMETERS 15.5 AMP PAGE TRK1–8 Sets the TRACK LEVEL parameter of track 1–8. 15.6 FX PAGE The parameters on the FX page control the track’s selected FX machine. Press [FUNC] + [FX] to select FX machine. The parameters vary depending on which FX machine is selected. For more information, please see “A.3 FX MACHINES” on page 98. 15.7 MOD PAGE 1 (LFO 1) The Low-Frequency Oscillator 1 is used to modulate the track’s parameters. Customize the LFO behavior, orientation, speed, and depth on this page. This page controls the behavior of LFO 1. The parameters on this page are the same as on the Audio track’s MOD PAGE 1. For more information, please see “12.12 MOD PAGE 1 (VOICE LFO 1)” on page 59. 15.8 MOD PAGE 2 (LFO 2) The Low-Frequency Oscillator 2 is used to modulate the track’s parameters. Customize the LFO behavior, orientation, speed, and depth on this page. This page controls the behavior of LFO 2. The parameters on this page are the same as on the Audio track’s MOD PAGE 1. For more information, please see “12.12 MOD PAGE 1 (VOICE LFO 1)” on page 59. 16. SAMPLING 16. SAMPLING Tonverk is a very competent and accessible sampler. It can sample audio from external sources via the external inputs, and it can also sample audio internally from Tonverk itself. There are two different sampling methods: you can use either the Recorder or the Auto Sampler. 16.1 THE SAMPLING MENU The SAMPLING menu within the Recorder provides settings that control various aspects of sampling. The maximum sampling time when using the SAMPLING menu is 6.06.06 minutes and this is always available even if a project’s RAM is fully utilized. Press [SAMPLING] to enter the SAMPLING SELECT screen, and then use [UP]/[DOWN] to select RE CORDER, and then press [YES] to access the SAMPLING menu. 16.1.1 REC NOW! Press [YES] to start sampling. Press [YES] to stop sampling. 16.1.2 SRC Source selects between different incoming audio sources to sample from. • IN A+USB L sets the input source to INPUT A and USB in L. • IN B+USB R sets the input source to INPUT B and USB in R. • IN + USB sets the input source to INPUT A+B and USB L+R. • MAIN sets the input source to Tonverk’s internal Mix track. the audio is sampled after the main FX. • TRK.1–8 sets the input source to one of Tonverk’s internal tracks 1–8. • BUS.1–4 sets the input source to one of Tonverk’s buses 1–4. 16.1.3 THR If you have selected to arm the sampler, the sampling begins when the incoming audio signal exceeds the threshold setting. Set the threshold high enough so that it is not triggered by background noise, but low enough that you capture all of the signal. 16.1.4 MON Selects the option to monitor and set the level of the incoming audio through Tonverk or not. 16.1.5 R.LEN Record Length sets the length of the sampling. With a setting of 1/16–16/1, the sampling length is decided by the time it takes the sequencer to advance a set number of steps at the current BPM. For example, the settings 1/16, 1/8, 1/2, 1/1, and 16/1 correspond to sampling durations of 1 sequencer step, 2 steps, 8 steps, 16 steps, and 256 steps, respectively. With the MAX setting, sampling continues until the maximum sampling time is reached or until you press [YES] to stop sampling. 13.1.6 R.STRT Record Start lets you set if the recorder will start sampling when you press [PLAY] or when the level of the audio source exceeds the threshold level set by THRES and with ARM set to ON 16.1.7 ARM Press [YES] to arm the sampler. The sampler is now in arm mode, and it will start sampling when the incoming audio exceeds the threshold level. See THR below. Press [SAMPLING] + [NO] to cancel.
チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。