D.3 NRPN VALUES AND PARAMETERS FOR THE SUBTRACKS SRC MACHINE

APPENDIX D: MIDI > D.3 NRPN VALUES AND PARAMETERS FOR THE SUBTRACKS SRC MACHINE · PDF p. 121–123 · OS 1.3.3

# D.3 NRPN VALUES AND PARAMETERS FOR THE SUBTRACKS SRC MACHINE

APPENDIX D: MIDI
NRPN
NRPN MSB
NRPN LSB
Audio tracks*
FX LFO1 depth
FX LFO2 speed
FX LFO2 multiplier
FX LFO2 fade
FX LFO2 waveform
FX LFO2 start phase /
FX LFO2 slew
FX LFO2 trig mode
FX LFO2 depth
Retrig on/off
Retrig time
Retrig velocity
FLTR env reset
FLTR env delay
FLTR key tracking
AMP mode
AMP reset
D.3 NRPN VALUES AND PARAMETERS FOR THE SUBTRACKS SRC MACHINE
NRPN MSB 1–8 = values control parameters for the eight separate subtracks (1–8).
NRPN
NRPN MSB
NRPN LSB
Audio tracks using the
Subtracks SRC machine
1–8
SRC tune
1–8
SRC play mode
1–8
SRC start
1–8
SRC length
1–8
SRC loop point
1–8
FLTR env reset
1–8
FLTR env delay
1–8
AMP mode
1–8
AMP env reset
1–8
FLTR attack
1–8
FLTR decay
1–8
FLTR sustain
1–8
FLTR release
1–8
FLTR frequency
1–8
FLTR resonance
1–8
FLTR type
1–8
FLTR env depth
1–8
FLTR base
1–8
FLTR width
1–8
FLTR frequency spread
1–8
AMP attack
1–8
AMP hold
1–8
AMP decay

APPENDIX D: MIDI
NRPN
NRPN MSB
NRPN LSB
Audio tracks using the
Subtracks SRC machine
1–8
AMP sustain
1–8
AMP release
1–8
AMP overdrive
1–8
AMP pan
1–8
AMP volume
1–8
VOICE LFO1 speed
1–8
VOICE LFO1 multiplier
1–8
VOICE LFO1 fade
1–8
VOICE LFO1 waveform
1–8
VOICE LFO1 start phase /
VOICE LFO1 slew
1–8
VOICE LFO1 trig mode
1–8
VOICE LFO1 depth
1–8
VOICE LFO2 speed
1–8
VOICE LFO2 multiplier
1–8
VOICE LFO2 fade
1–8
VOICE LFO2 waveform
1–8
VOICE LFO2 start phase
VOICE LFO2 slew
1–8
VOICE LFO2 trig mode
1–8
VOICE LFO2 depth
1–8
MOD ENV attack
1–8
MOD ENV decay
1–8
MOD ENV sustain
1–8
MOD ENV release
1–8
MOD ENV reset
1–8
MOD ENV delay
1–8
MOD ENV depth

APPENDIX E: SFZ SUPPORT
APPENDIX E: SFZ SUPPORT
The primary and best-supported method of specifying multi-sampled instruments for the Multi player
machine and the sample sets for the Subtracks machine on Tonverk is the native mapping format, which is
found in the .eldrum and .elmulti files included in the factory library.
However, a subset of the SFZ format can be loaded by Tonverk. This document describes the capabilities
and limitations of that subset.
E.1 HEADERS
Tonverk supports the following headers. Note that all headers besides <region> are optional.
• <control>
• <global>
• <master>
• <group>
• <region>
All of the above, aside from <control>, support the same opcodes but have different scope and override
semantics (see https://sfzformat.com/headers for more information on headers).
E.1.1 OTHER HEADERS
• <curve> headers are allowed to be present, but are ignored.
• <effect>, <midi>, and <sample> headers are not supported, and files containing them will fail to load.
E.2 CONTROL OPCODES
Under the <control> header, the following opcodes are supported:
• default_path sets the path where files are loaded relative to. Please note that the behavior of some
players, which allows file-name prefixes in addition to distinct pathelements, is not supported.
• note_offset transposes all regions by a number of semitones.
• octave_offset transposes all regions by a number of octaves.
For more information about opcodes, please see https://sfzformat.com/opcodes/
E.2.1 IGNORED CONTROL OPCODES
For convenience, the following opcodes are ignored and will not cause an error if they are present:
• hint_load_method
• label_cc_*
• set_cc_*
Any other opcodes provided under the <control> header will result in an error.
E.3 REGION OPCODES
Headers <global>, <master>, <group>, and <region> all support the same set of opcodes.
Pitch values can be specified as numeric MIDI key values or in IPN, where MIDI note 0 is called “C-1”
(and consequently, middle C is C4).
E.3.1 REQUIRED OPCODES
A region (or a group, master, or global header preceding it) must minimally specify a sample (sample=...)
and a pitch (via either key=... or pitch_keycenter=...). Regions that fail to meet this criterion will be
ignored.
The sample opcode is a file path, relative to the location of the SFZ file. Use UNIX-style paths
(with forward slashes) for best results.
Special rules for file names.
• Space (blank) characters are allowed.
• Equals (=) and balanced angle brackets (e.g. My<Sample>.wav) are not allowed.
• Comment-opening tokens (// or /*) are forbidden.
• Any trailing blank characters are ignored.

チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。