6.2 PARAMETER EDITING
6. INTERACTING WITH THE DIGITONE II > 6.2 PARAMETER EDITING · PDF 第 18–19 · OS 1.10D
# 6.2 PARAMETER EDITING 6. INTERACTING WITH THE DIGITONE II 6. INTERACTING WITH THE DIGITONE II The screen shows all the information needed for real-time interaction and editing on the Digitone II. The eight DATA ENTRY knob parameters shown will vary depending on the given situation. Below is the main interface screen of the MOD page. 1. The current bank and pattern. 2. The current pattern name. 3. The selected TRIG mode. 4. The current tempo. 5. Eight track parameters. They show what the DATA ENTRY knobs control and their current parameter values. 6. Parameter page indicator. Indicates the number of pages for the selected parameter section and which page is currently selected. 7. The main level setting of the active track. Use the LEVEL/DATA knob to change the volume setting. 8. The current active track. 9. Track type. Audio (SYN) track or MIDI (MID) track. The Digitone II features a screen saver that dims the screen after 5 minutes of inactivity and turns off the screen after 60 minutes. Press any key or move any controller to wake the screen. 6.1 SCREEN NAVIGATION Use the [ARROW] keys [UP], [DOWN], [LEFT] or [RIGHT] to navigate menus or sub-menus. The LEVEL/DATA knob can be used to scroll through menus and lists quickly. [YES] is used to affirm, select, enter sub-menus and tick/untick boxes. [NO] is used to negate, deselect or go back one or more steps. When in a menu or sub-menu, the [NO] key can be used to go back, one step at a time, all the way to the main screen. 6.2 PARAMETER EDITING The DATA ENTRY knobs are used to change the values of the track parameters. The positions of the pa rameters on the screen correspond to the physical locations of the knobs on the front panel. Some of the parameters on the screen tell you what DATA ENTRY knob controls that particular parameter. For example “(E)” in the PAGE SETUP menu. • The parameters are adjusted in larger increments if you press down the DATA ENTRY knob while turning it. This makes it quicker to sweep through the whole parameter range. • Press DATA ENTRY knob + [NO] to reset the parameter to the default value. • Press [PARAMETER] key + [PLAY] to reset all the parameters in the selected parameter page to default values. • Press and hold a [PARAMETER] key to see the values for all parameters on that page. 6. INTERACTING WITH THE DIGITONE II 6.2.1 PARAMETER VALUE JUMP Pressing [FUNC] while editing certain parameters will make the parameter values jump to appropriate positions. The NOTE parameter, for example jumps between octaves and the delay time jumps between BPM related tempo settings. 6.2.2 CONTROL ALL If you press and hold [TRK] and change a parameter setting, this change will affect this parameter in all the audio tracks in the pattern. Press [NO] before you release [TRK] to revert the parameter changes. In the SETUP menu, you have the possibility to select which tracks should be affected by the control all functionality. For more information, please see “9.6.1 KIT” on page 35. • Control all operations also affects the active track, whether it is selected to be affected or not. • The control all functionality is not available for the MIDI tracks. 6.2.3 [FUNC] KEY PRESS COMBINATIONS The standard way to use the [FUNC] key in combination with other keys, is to press and hold [FUNC] and then press the second key in the combination. 6.3 QUICK SCROLLING Scroll through menus using the LEVEL/DATA knob. Quick scrolling is possible on many menus. Press [FUNC] + the [UP] or [DOWN] keys to move the cursor one menu page. 6.4 COPY, CLEAR, AND PASTE Copy, clear and paste commands are available in a lot of contexts. Pressing [FUNC] + [RECORD] to copy. Press [FUNC] + [STOP] to paste. Press [FUNC] + [PLAY] to clear. Paste and clear operations are undone by repeating the key press combination. Please see the different sections in the manual for more informa tion on when these commands are available. For more information, please see “16. KEY COMBINATIONS” on page 84. The copy clipboard can only hold one item at a time. When you perform a copy command, the item copied replaces any earlier copied items. For example, you can not have both a trig and a pattern copied at the same time. 6.5 THE NAMING SCREEN The naming method is identical for the various naming situations that appear when you save presets, proj ects et cetera. The [LEFT] and [RIGHT] arrow keys are used to navigate between the characters. Turning the LEVEL/ DATA knob or pressing the [UP] or [DOWN] arrow keys selects the characters. [FUNC] + [NO] erases characters. [FUNC] + [YES] inserts space. Press [SETTINGS] to create a random name. Press and hold [FUNC] to access the Pop-up Naming menu. 6.5.1 POP-UP NAMING A convenient way of naming is to open a pop-up menu that shows all available letters, symbols, and digits. Press and hold the [FUNC] key when you are on the NAMING screen to access the Pop-up Naming screen.
章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。