10.7 VOICE SETUP MENU
10. THE SEQUENCER > 10.7 VOICE SETUP MENU · PDF 第 47–48 · OS 1.10D
# 10.7 VOICE SETUP MENU 10. THE SEQUENCER OR All trigs from both generator 1 or 2 are placed on the track. XOR Trigs from both generator 1 or 2 are placed on the track unless they are added to the same sequencer step. AND Only trigs added to the same sequencer step by generator 1 and 2 are placed on the track. SUB Trigs from generator 1 are placed on the track unless generator 2 adds a trig on the same step as generator 1. In Euclidean mode, please note that if you press any already generated trigs, they will remain in regular sequencer mode when you switch Euclidean mode off. 10.7 VOICE SETUP MENU Press [VOICE SETUP] to open the VOICE SETUP menu, where you handle the allocation of the Digitone II’s 16 voices. In this menu, you can also make the settings for unison and voice stealing. Press [TRK] + [TRIG 1–16] to select which track to edit. At the top of the screen, you can see what track is selected. The center of the screen shows the currently playing voices. Use the DATA ENTRY knobs to change the settings. Press [NO] to exit the menu. The voice settings are stored in the active pattern. VOICE STEAL The Digitone II has 16 voice polyphony. VOICE STEAL sets the rules for how voices are stolen (which voice is taken when you play a new note) when you use more than 16 voices at the same time. The VOICE STEAL parameter affects the whole pattern. CYCLE The first played note is stolen first. TRACK Track priority. Notes played on track 1 has priority over notes played on track 2–16. Track 2 notes over track 3–16. Track 3 notes over track 4–16 etc. LO Lowest note is stolen first HI Highest note is stolen first. REUSE Sets if the same note played twice should reuse the same voice, or cycle to use another free voice. ON Reuses the same voice. Useful for staccato effects and drums. OFF Cycles to use another voice. Good for piano-like sounds and pads. VOICES Sets the number of voices (1–16) you want to lock to a specific track. A locked voice cannot be used or stolen by another track. If you lock voices to a track, the track cannot use more voices than the ones that are locked to it. The first number shows the number of locked voices to the track. The number in brackets shows how many unlocked voices that remain. If you set the parameter to DYN (dynamic) it will use any available voices to play its preset. The number of voices that are used to play a preset is also affected by the PLAY MODE setting in the SETUP menu. For more information, please see “9.6 THE SETUP MENU” on page 35. STATE Unison State turn unison on/off. Unison gives the possibility to add several voices to play the same note. V.AMNT Unison Voice Amount sets the number of voices that plays for each note. [FUNC] + [VOICE SETUP] toggles unison on/off. SPREAD Unison Spread adds pan and detune to the unison voices. 10. THE SEQUENCER You can copy the settings in the VOICE menu and paste it to another pattern. In the VOICE menu, press [FUNC] + [RECORD] to copy the parameter settings. Change pattern and open VOICE menu, and then press [FUNC] + [STOP] to paste the settings. 10.8 MICRO TIMING Here you can add micro timing to a note trig, moving it ahead or behind the beat. Micro timing can be customized on any of the sequencer steps on both audio and MIDI tracks. In GRID RECORDING mode, press and hold one or several [TRIG] keys and then press [LEFT]/[RIGHT] to access the pop-up Micro timing menu that shows the time offset for the chosen sequencer step(s) on the active track. Press [LEFT]/ [RIGHT] to adjust the time offset. To exit the MICRO TIMING menu, release the [TRIG] key(s). The micro timing settings are stored in the active pattern. 10.9 RETRIGS Retrigs can be customized on any of the sequencer steps on the audio tracks (the retrig function is not available on the MIDI tracks). In GRID RECORDING mode, press [TRIG PARAMETERS] twice to access the RETRIG PARAMETERS page. Hold one or several [TRIG] keys and then set the desired retrig options for the trig(s). For more information about the parameters on this page, please see “11.3 TRIG PAGE 2” on page 58. 10.10 QUANTIZE MENU The quantization affects all micro timed and off grid trigs on the sequencers tracks. Press [FUNC] + [TRIG PARAMETERS] to access this menu. Change settings with DATA ENTRY knob E and H. TRACK affects all the trigs of the active track in real time. The higher the quantize value, the more the trigs will be quantized. Press [TRIG 1–16] key to select track to quantize. PATTERN affects all the trigs of all tracks in the pattern in real time. The higher the quantize value, the more the trigs will be quantized. Press [NO] to exit the menu. 10.11 PAGE SETUP MENU You can set the length and timing of the pattern and the tracks in this menu. The sequencer has up to 128 steps spread over 8 pages with 16 steps each. The PAGE SETUP menu has two modes. In PER PATTERN mode all tracks share the same length. In PER TRACK mode, each track can have different lengths. Press [FUNC] + [PAGE] to access the PAGE SETUP menu. Press [FUNC] + [YES] to toggle between the two modes. Use the DATA ENTRY knobs to adjust the settings.
章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。