11.3 TRIG PAGE 2

11. TRACK PARAMETERS > 11.3 TRIG PAGE 2 · PDF 第 58–59 · OS 1.10D

# 11.3 TRIG PAGE 2

11. TRACK PARAMETERS
FLT.T
Filter Trig controls if the filter envelope will be trigged or not.
FILL
Fill is a separate trig condition that determines if a trig is active (plays) or not depending on if the device
is in FILL mode or not. For more information, please see “10.12.4 FILL MODE” on page 52, and “10.12.3
TRIG CONDITIONS AND CONDITIONAL LOCKS” on page 51.
ON, A trig with FILL set to ON, plays when FILL mode is active.
OFF, A trig with FILL set to OFF plays when FILL mode is not active.
The sequencer needs to be in FILL mode to activate the FILL trig condition. For more
information, please see “10.12.4 FILL MODE” on page 52.
COND
(Trig Condition) when you add a conditional lock, COND sets the Trig Condition with which a set of con
ditional rules can be applied to any trig, using a conditional parameter lock. For more information, please
see “10.12.3 TRIG CONDITIONS AND CONDITIONAL LOCKS” on page 51.
11.3 TRIG PAGE 2
Here you set the behavior of retrigs that are added to note trigs placed in the sequencer. On this page you
also control the portamento. Change settings using the DATA ENTRY knobs. These general settings all
affect note trigs placed in the sequencer.
Retrigs can be customized on any of the sequencer steps on the audio tracks (the retrig function is not
available on the MIDI tracks). In GRID RECORDING mode, press [TRIG PARAMETERS] twice to access the
RETRIG PARAMETERS page. Hold one or several [TRIG] keys and then set the desired retrig options for
the trig(s). The RETRIG PARAMETERS page shows the retrig actions for the chosen sequencer step(s) on
the active track. The retrig settings are stored in the active pattern.
RTRG
Retrig enables a number of trig repeats on placed trigs. Use DATA ENTRY knob A to turn retrig on/off.
For information on setting retrig locks on specific trigs in the sequencer, please see “10.9 RETRIGS” on
page 48.
VFAD
Velocity Fade sets the velocity curve fade out/fade in of the retrig (-64–64). -64 corresponds to a
complete fade out during the set length, -32 fades out to half the velocity during the set length, 0 equals
a flat velocity curve with no fade, 32 fades into half velocity during the set length and 64 fades in com
pletely to full velocity during the set length. Please note that the effects of the VFAD setting is also
dependent on the VEL setting on TRIG PAGE 1.
LEN
Length sets the duration of the retrig velocity curve in fractions of, or rational or integer multiples of, a
step (0,125–INF). 1/16 is the nominal length of one step. This setting affects the behavior of the velocity
curve by defining the boundaries of its envelope.
RATE
Rate sets the retrig rate. 1/16 is the nominal retrig rate, one trig per step. 1/32 corresponds to two trigs
per step and so on. To do triplets, for example, set the retrig rate to 1/12 (or 1/24).

11. TRACK PARAMETERS
PTIM
Portamento Time sets the time for the portamento.
PORT
Portamento turns the portamento on/off. Please note that this parameter is only available on audio
tracks.
For more information, please see “5.3.1 AUDIO TRACKS AND MACHINES” on page 16.
11.4 SYN PAGES
The parameters on the SYN pages control the selected SYN machine, and these parameters vary depend
ing on what machine is selected. The SYN machines are different synthesis engines with unique functional
ity. In the SYN machine section you also find the MIDI machine that lets you control external, MIDI equipped,
gear. You can assign any SYN machine to any track. For more information, please see “A.2 SYN MACHINES”
on page 89.
Press [SYN] to access these parameter pages.
The screen shot shows the first page for the FM Tone machine.
11.5 FLTR PAGE 1
The parameters on the FLTR page 1 control the filter, and these parameters vary depending on what FLTR
machine is selected. The FLTR machines are a collection of different filters and EQ. On this page you also
find the filter envelope. For more information, please see “A.3 FLTR MACHINES” on page 101.
Press [FLTR] to access this parameter page.
The screen shot shows the page for the Multi-mode FLTR machine.
11.6 FLTR PAGE 2
On FLTR page 2, you will find the parameters that control the base-width filter and a number of parameters
that affects the selected filter machine on FLTR page 1.
The base-width filter is basically a Highpass filter and a Lowpass filter connected in tandem. The filters
BASE and WDTH parameters define the base-width filters frequency range.

章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。