15.4 FLTR PAGE
15. MIX TRACK PARAMETERS > 15.4 FLTR PAGE · PDF 第 69–70 · OS 1.3.3
# 15.4 FLTR PAGE 15. MIX TRACK PARAMETERS RVEL Repeat velocity sets the velocity curve fade-out and fade-in of the retrig. -1 corresponds to a complete fade out during the set length, -0,5 fades out to half the velocity during the set length, 0 equals a flat velocity curve with no fade, 0.5 fades into half velocity during the set length, and 1 fades in completely to full velocity during the set length. Please note that the effects of the VFAD setting is also dependent on the VEL setting on TRIG PAGE 1. COND (Trig Condition) when you add a conditional lock, COND sets the Trig Condition with which a set of con ditional rules can be applied to any trig, using a conditional parameter lock. For more information, please see “10.10.2 TRIG CONDITIONS AND CONDITIONAL LOCKS” on page 45. 15.3 SRC PAGE On this page you control aspects related to the incoming audio from extrnal sources (USB and IN A/B). IN A/IN B The level parameters set the level of the incoming audio from the USB and IN A/B inputs. APAN/BPAN The pan parameters position the audio from USB and IN A/B in the stereo field. The knob function is bipolar with 0 being the balanced midpoint, L64 sends all sound to the left channel and R63 sends all sound to the right. ROUT/ROUT The routing parameters select where to route the audio from USB and IN A/B. This parameter’s routing switches are shown with “A” in the sound architecture illustrations. For more information, please see “4. TONVERK SOUND ARCHITECTURE” on page 17 and “4.4 THE ROUTING MENU” on page 17. • MIX AB is the default setting and routes the audio though the Main FX to the A/B outputs and the Headphones. • OUT AB routes the audio to the AB outputs and the Headphones without going through the Mixer and Main FX. • OUT CD routes the audio directly to the C/D outputs. • OUT EF routes the audio directly to the E/F (HEADPHONES) outputs. • BUS 1–4 routes the audio to Bus 1–4) • TRK 1–8 routes the audio to Track 1–8) 15.4 FLTR PAGE HP.MON Here you set the level of the audio sent from the mixer to the headphones (Output EF). You can find this parameter’s position in the signal flow, shown with an “E”, in the sound architecture illustrations. For more information, please see “4. TONVERK SOUND ARCHITECTURE” on page 17. 15. MIX TRACK PARAMETERS 15.5 AMP PAGE TRK1–8 Sets the TRACK LEVEL parameter of track 1–8. 15.6 FX PAGE The parameters on the FX page control the track’s selected FX machine. Press [FUNC] + [FX] to select FX machine. The parameters vary depending on which FX machine is selected. For more information, please see “A.3 FX MACHINES” on page 98. 15.7 MOD PAGE 1 (LFO 1) The Low-Frequency Oscillator 1 is used to modulate the track’s parameters. Customize the LFO behavior, orientation, speed, and depth on this page. This page controls the behavior of LFO 1. The parameters on this page are the same as on the Audio track’s MOD PAGE 1. For more information, please see “12.12 MOD PAGE 1 (VOICE LFO 1)” on page 59. 15.8 MOD PAGE 2 (LFO 2) The Low-Frequency Oscillator 2 is used to modulate the track’s parameters. Customize the LFO behavior, orientation, speed, and depth on this page. This page controls the behavior of LFO 2. The parameters on this page are the same as on the Audio track’s MOD PAGE 1. For more information, please see “12.12 MOD PAGE 1 (VOICE LFO 1)” on page 59.
章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。