← 検索に戻る

11.10 MOD PAGE 2

11. TRACK PARAMETERS > 11.10 MOD PAGE 2 · PDF p. 63–64 · OS 1.10D

# 11.10 MOD PAGE 2

11. TRACK PARAMETERS
11.9 MOD PAGE 1
The MOD pages contain three LFOs (two for tracks that use MIDI machines). The Low-Frequency Oscilla­
tor can be used to modulate track parameters. Customize the low-frequency oscillator behavior, orientation,
speed, and depth on this page. This page controls the behavior of LFO 1
Press [MOD] to access this parameter page.
SPD
Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The knob
is bipolar. The LFO cycle can be played backward by using negative values.
MULT
Multiplier multiplies the SPD parameter by the set factor either by multiplying the current tempo (BPM
settings), or by multiplying a fixed tempo of 120 BPM.
FADE
Fade In/Out makes it possible to fade in/fade out the LFO modulation. The knob is bipolar. Positive val­
ues give a fade-out, negative values give a fade in. 0 gives no fade in/fade out. (-64–63)
DEST
Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect
the sound by highlighting a destination. Press [YES] to confirm the selection. Press [NO] to cancel and
revert to previous selection. Press [FUNC] and then turn the knob to snap to destination sections. For
more information, please see “APPENDIX D: MODULATION DESTINATIONS” on page 118
WAVE
Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are
bipolar. The Exponential and Ramp are unipolar.
SPH
Start Phase sets the point within the wave cycle where the LFO will start when it is trigged. 0 makes the
LFO start at the beginning of a complete wave cycle, 64 makes it start at the center. A small square at
the start of the waveform shows that the wave cycle starts at a zero-crossing. If WAV is set to RND then
the SPH parameter changes to SLEW and adds slew to the transitions in the waveform.
MODE
Trig Mode sets how the LFO will act when a note is trigged.
• FREE is the default free-running mode. It makes the LFO run continuously, never restarting or
stopping even if notes are trigged.
• TRIG makes the LFO restart when a note is trigged.
• HOLD makes the LFO run free in the background, but when a note is trigged the LFO output level is
latched and held still until the next note is trigged.
• ONE The LFO starts when a note is trigged, then runs to the end of the waveform and then stops.
This makes the LFO function similar to an envelope.
• HALF The LFO starts when a note is trigged, then runs to the middle of the waveform and then stops.
DEP
Depth sets the depth and polarity of the LFO modulation. Both negative and positive modulation depth is
possible. A center setting, 0.00, equals no modulation depth.
11.10 MOD PAGE 2
MOD page 2 page contains the same parameters as LFO page 1, but controls the behavior of LFO 2.

11. TRACK PARAMETERS
11.11 MOD PAGE 3
MOD page 3 page contains the same parameters as LFO page 1, but controls the behavior of LFO 3.
Please note that MIDI tracks only have two LFOs.
LFO WAVEFORMS AND TRIGMODES
TRIG
HALF
TRIG
ONE
TRIG
TRIG
HOLD
TRIG
TRIG
TRIG
TRIG
FREE
TRI
SINE
SQR
SAW
EXPO
RAMP
RAND
LFO TRIG MODE
WAVEFORM
LFO SPEED SETTINGS
The table below shows the LFO speed measured in sequencer steps using different combinations of SPD
and MULT (set to a BPM value) settings. For example, a value of 8 in the table means that the LFO will do
one full cycle in the time it takes the sequencer to advance eight steps.
MULT
S
P
D
1K
2K
2048
1024
1024
1/2
1/2
1/4
1/2
1/4
1/8
1/2
1/4
1/8
1/16
1/2
1/4
1/8
1/16
1/32
1/2
1/4
1/8
1/16
1/32
1/64

チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。