14.5 EXIT
14. STARTUP MENU > 14.5 EXIT · PDF p. 81–82 · OS 1.10D
# 14.5 EXIT 14. STARTUP MENU 14. STARTUP MENU To access this menu, hold down the [FUNC] key while powering up the Digitone II. From here you can per form a variety of tasks. To choose the different alternatives, press the corresponding [TRIG] key. 14.1 TEST MODE To enter this mode, press the [TRIG 1] key. For testing purposes, a short sound is heard through all outputs of the unit. If you have any trouble with your Digitone II and suspect it may be due to a hardware problem, perform this self-test. The [UP] and [DOWN] keys can be used to scroll through the test log. A fully functional device should not report any errors. If it does report an error, please contact Elektron support or the retailer where you bought your Digitone II from. 14.2 EMPTY RESET To perform this operation, press the [TRIG 2] key. All patterns and presets will be erased. The data on the +Drive remains intact. 14.3 FACTORY RESET When performing a factory reset on the Digitone II, it will overwrite and re-initialize the active RAM project (including all pattern and global data). The +Drive project slot 1 will be overwritten and re-initialized with fac tory preset patterns, presets and settings. Preset bank A and B will be overwritten with the factory presets. If you wish to keep the active project, remember to save it to a +Drive project slot higher than 1 before you perform a factory reset. To perform a factory reset, press the [TRIG 3] key. 14.4 OS UPGRADE Use this menu option if you for some reason cant upgrade the Digitone II OS using the standard procedure in the SYSTEM menu. To send the OS file, use our free Elektron Transfer software. The Elektron Transfer can be downloaded from the Elektron website. 1. Download the Digitone II OS file from the Elektron website. 2. Connect the Digitone II’s MIDI IN port to the MIDI OUT port of the computer’s MIDI interface. 3. Hold down the [FUNC] key while powering on Digitone II. This takes you to the STARTUP menu. 4. Press the [TRIG 4] key to enter OS UPGRADE mode. 5. Open the Transfer application on your computer. On the Transfer CONNECTION page, click “go to the SYSEX TRANSFER page”. 6. On the SYSEX TRANSFER page, click “OS Upgrade via device startup menu”, and then follow the on- screen instructions. When the update is done, the Digitone II will reboot. USB MIDI transfer is not possible when upgrading the OS from the STARTUP menu. 14.5 EXIT Press the [TRIG 5] key to exit the STARTUP menu. 15. SETUP EXAMPLES 15. SETUP EXAMPLES The Digitone II likes to play with other machines. Whether it uses its ability to sync and play with legacy machines or controls other synthesizers: Digitone II gets along with other gear. 15.1 DIGITONE II WITH A MONOPHONIC BASS MACHINE The DIN sync capabilities of the Digitone II allows you to use gear from yesteryear. In this example, a legacy monophonic bass machine is used alongside the Digitone II. The Digitone II can stop, start and control the tempo of the bass machine. 1. Prepare a bassline pattern on the bass machine. 2. Connect the output of the bass machine to the mixer using a Mono jack 6.3 mm male cable. 3. Connect the Digitone II audio outputs to the mixer using 2 x Mono or Stereo jack 6.3 mm male cables. 4. Use a DIN connector cable to connect the MIDI OUT of the Digitone II to the SYNC IN of the bass machine. 5. On the Digitone II, press [SETTINGS], and then navigate to MIDI CONFIG > PORT CONFIG and set OUT PORT CONFIG to DIN24. 6. Press [PLAY] on the Digitone II. 15.3 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS
チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。