9.11 CHAINS
9. THE SEQUENCER > 9.11 CHAINS · PDF p. 46–47 · OS 1.40A
# 9.11 CHAINS 9. THE SEQUENCER 9.10.6 COPY, PASTE AND CLEAR OPERATIONS Patterns, tracks, track pages, and trigs can be copied, pasted and cleared. The active pattern can be copied to another location in the same bank or in another bank. To perform a pattern copy operation, GRID RECORDING mode must be deactivated. Copy the pattern by pressing [FUNC] + [RECORD]. Select another pattern, and then press [FUNC] + [STOP] to paste the copied pattern to this location. Press [FUNC] + [PLAY] to clear all the trigs in the current pattern. Individual sequencer tracks can be copied, pasted and cleared in the same way as patterns. To do so, GRID RECORDING mode must be active. A single track page may also be copied, pasted and cleared. It is similar to copying/pasting/clearing a track, but will only affect the active track page. Select the track page of choice by pressing the [PAGE] key. Copy by pressing [PAGE] + [RECORD]. Select a new track page and press [PAGE] + [STOP] to paste. Press [PAGE] + [PLAY] to clear the active track page. Trigs, complete with all parameter lock settings, can be copied, pasted and cleared as well. GRID RE CORDING mode needs to be active to access this functionality. Press and hold a [TRIG] key and press [RECORD] to perform the copy operation. Paste by holding another [TRIG] key and pressing [STOP]. It is also possible to copy more than one trig. Press and hold the trigs you wish to copy, and then press [RECORD]. Press and hold the [TRIG] key to where you want to paste, and then press [STOP] to paste the copied sequence of trigs. When pasting, the copied trigs are placed in the same relation to each other as they had when they were copied. The destination trig acts as the starting point for the sequence of copied trigs. Clear trig locks by holding one or more trigs and press [PLAY]. You can undo a copy, paste, and clear operation by repeating the key presses. It is possible to copy, clear and paste a pattern without leaving the active pattern. To copy, press and hold [PTN] + [TRIG] key to select the pattern you wish to copy. Then press [RECORD]. Let go of the [TRIG] key and then press and hold the [TRIG] key(s) to where you want to paste the pattern. Finally, press and hold [STOP] until the count down finishes to paste the pattern. To clear, press and hold [PTN] + [TRIG] key(s) to select the pattern(s) you wish to clear. Then press and hold [PLAY] until the count down finishes to clear the pattern(s). 9.10.7 TEMPORARY SAVE AND RELOAD PATTERN COMMANDS Patterns can instantly be saved to a temporary memory space and then reloaded again from this space. • To perform a temporary save of the active pattern, press [FUNC] + [YES]. This is useful in order to create a restore point when you are live tweaking, but without permanently save your changes. • To perform a temporary reload of the active pattern, press [FUNC] + [NO]. It will the reload the pat tern from when you last used the temporary save command. If you have not done any temporary save, then the pattern will reload from the permanently saved state. The TEMPORARY SAVE PATTERN and TEMPORARY RELOAD PATTERN commands are great when improvising live. Any changes made to the active pattern, like adding bass line notes or using CONTROL ALL , can immediately be undone. And at the same time, the saves and reloads will not affect the pattern in a permanent way. The TEMPORARY SAVE PATTERN command will not save the pattern permanently and any changes will be lost if you load another project. If you wish to save your changes per manently, you should use SAVE TO PROJ in the PATTERN MENU. For more information, please see “14.3 PATTERN” on page 73. 9.11 CHAINS Chains are sequences that consist of more than one pattern. You can use chains to preselect and automate in what order you want your patterns to play. 9. THE SEQUENCER You can create one chain and it can contain any pattern in bank A–H. The chain can be to 64 patterns long. 1. Press [PTN], and then press [FUNC] + [YES] to open the chain creator screen. 2. Use the [LEFT]/[RIGHT] keys to select a bank (if you want to select a pattern from another bank than the current). Then press [TRIG 1–16] to select a pattern. Repeat until you have created the desired chain. 3. (Optional) Press [FUNC] + [LEFT] to delete the last pattern from the chain. 4. Press [YES] to confirm the pattern chain and close the chain creator screen. Press [NO] if you wish to cancel the pattern chain and close the chain creator screen. 5. Press [PLAY] to start the sequencer and play the chain. The chain will be looped once the final pattern of the chain has played. To exit chain mode, select a pattern or song using the normal selection process. There is also a legacy procedure for how you create chains that also can be used. 1. Press and hold [PTN] and then press a [TRIG 1–16] key to select the first pattern in the chain. 2. Release the [PTN] key and then press [TRIG 1–16] keys in the same order as you want the chained patterns to play. Keep a previous [TRIG] key pressed while you press the next one, the one after that and so on. You can press the same [TRIG] key again if you wish to add the pattern multiple times in a row. If you want to add a pattern from another bank, use the [LEFT]/[RIGHT] keys to select a bank and then press [TRIG 1–16] to select pattern. 3. Press [PLAY] to start the sequencer and play the chain. The chain will be looped once the final pattern of the chain has played. Please note that the chain will be lost when you create a new chain or when you select a new bank/pattern. Chains cannot be saved and will be lost when you switch the Syntakt off. • Chains can be created while the sequencer is running. • You can also use MIDI program change messages from an external device to change patterns on the Syntakt. For more information, please see “14.4.1 SYNC” on page 75. 9.12 SONG MODE A song is an arrangement of patterns set up to play in sequence. Each row in the SONG mode arrangement can have separate settings for pattern, row repeat, row length, tempo, and mute. A song can be up to 99 rows in length, and each project can contain up to 16 songs. 9.12.1 THE SONG EDIT SCREEN Press [SONG MODE] and then press [YES] to enter SONG mode. The song selected will be the one that was last played or edited. Press [SONG MODE] and then press [RIGHT] to open the SONG EDIT screen. Use the [ARROW] keys to navigate the song rows and columns, highlighting the parameter you wish to edit, and then use LEVEL/DATA or any DATA ENTRY knob to edit the selected function. 1. SONG ROW (Range 01–99) 2. LABEL lets you select a keyword for the row. The keyword is related to song structure, e.g., Verse, Chorus, and Fill. It can also be the pattern name. 3. PTN lets you select the pattern to be played on the row. Press [FUNC] while turning the knob to change banks quickly. 4. ROW PLAY COUNT The number of times the row plays before the song advances to the next row..
チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。