16.2 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS
16. SETUP EXAMPLES > 16.2 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS · PDF p. 85–87 · OS 1.40A
# 16.2 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS 16. SETUP EXAMPLES 16. SETUP EXAMPLES The Syntakt likes to play with other machines. Whether it uses its ability to sync and play with legacy ma chines or controls other synthesizers: Syntakt gets along with other gear. 16.1 SYNTAKT WITH A MONOPHONIC BASS MACHINE The DIN sync capabilities of the Syntakt allows you to use gear from yesteryear. In this example, a legacy monophonic bass machine is used alongside the Syntakt. The Syntakt can stop, start and control the tempo of the bass machine. 1. Prepare a bassline pattern on the bass machine. 2. Connect the output of the bass machine to the mixer using a Mono jack 6.3 mm male cable. 3. Connect the Syntakt audio outputs to the mixer using 2 x Mono or Stereo jack 6.3 mm male cables. 4. Use a DIN connector cable to connect the MIDI OUT of the Syntakt to the SYNC IN of the bass machine. 5. On the Syntakt, press [SETTINGS], and then navigate to MIDI CONFIG > PORT CONFIG and set OUT PORT CONFIG to DIN24. 6. Press [PLAY] on the Syntakt. 16.2 CONTROLLING A SYNTHESIZER USING THE MIDI TRACKS 16. SETUP EXAMPLES Syntakt has extensive capabilities to use its sequencer’s MIDI tracks to control other MIDI-equipped synthesizers. 1. Use a standard MIDI cable to connect the Syntakt MIDI OUT jack to the synthesizer’s MIDI IN jack. 2. On the Syntakt, press [SETTINGS], and then navigate to MIDI CONFIG > PORT CONFIG and set OUT PORT FUNC to MIDI. 3. In the same menu set OUTPUT to MIDI. 4. Press [FUNC] + [SYN], and then use the [ARROW] keys to navigate to the MIDI machine, and then press [YES] to select the MIDI machine on the active track. 5. Press [SYN] and use the CHAN parameter to select a MIDI channel that the track will output its data to. 6. Make sure to set your synthesizer to receive MIDI input in a way that corresponds to the settings you made in the Syntakt. You are now ready to use the Syntakt sequencer to control your synthesizer. For more information about using the Syntakt sequencer, please see “9.1 SEQUENCER TEMPO” on page 36. 17. USEFUL KEY COMBINATIONS 17. USEFUL KEY COMBINATIONS Use the key combinations below to quickly perform certain tasks. GENERAL [FUNC] + [REC] performs a copy command. Action depends on the currently active page or mode. [FUNC] + [PLAY] performs a clear command. Action depends on the currently active page or mode. [FUNC] + [STOP] performs a paste command. Action depends on the content that was copied. Press and hold [TRK] and change a parameter setting, then this change will affect this parameter in all the audio tracks in the pattern. TRACK/PATTERN/BANK SELECT [TRK] + [TRIG 1–12] keys to select a track. [PTN] + [TRIG 1–16] keys to select a pattern. [BANK] + [TRIG 9–16] keys to select a bank. NAMING [FUNC] + [ARROW] (on the NAMING screen) to choose a letter. [FUNC] + [NO] (on the NAMING screen) to erase a letter. SAVING AND RELOADING [FUNC] + [SETTINGS] saves the active Project. [FUNC] + [YES] temporary saves the active Pattern. [FUNC] + [NO] temporary reloads the active Pattern. [PARAMETER] key + [NO] reloads all parameters on that parameter page from its last saved state. [TRK] + [TRIG 1–12] + [NO] reloads the sound from its last saved state. [TRIG] + [SONG MODE] save the sound of a trig as a Sound, taking all parameter locks in consideration. MENU ACCESS [FUNC] + [SONG MODE] opens the SOUND SETTINGS menu. [FUNC] + [FX] opens the ANALOG FX BLOCK ROUTING menu. [FUNC] + [TRIG] opens the QUANTIZE menu. [FUNC] + [SYN] opens the MACHINE menu. Press [SYN] twice rapidly to open the MACHINE menu. [FUNC] + [FLTR] opens the DELAY menu. [FUNC] + [AMP] opens the REVERB menu. [FUNC] + [LFO] opens the MIXER menu. [FUNC] + [PTN] (long press) opens the METRONOME menu. [FUNC] + [PAGE] opens the pattern/track SCALE menu. [FUNC] + [TRK] (long press) opens the KEYBOARD SETUP menu. [FUNC] + [UP]/[DOWN] opens the MODIFIER SETUP menu. SEQUENCER [FUNC] + [TEMPO] to tap tempo. [FUNC] + [PTN] (short press) switches the metronome ON/OFF. [LEFT/RIGHT] to nudge tempo (when sequencer is playing). [FUNC] + [LEFT/RIGHT] moves all trigs a whole step, left or right (when in GRID RECORDING mode). [TRIG] key (hold) + [UP/DOWN], opens the RETRIG menu and turns retrig on and sets the retrig RATE for the trig (when in GRID RECORDING mode).
チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。