← 返回搜索

12.6 AMP PAGE 1

12. FX TRACK PARAMETERS > 12.6 AMP PAGE 1 · PDF 第 64–66 · OS 1.40A

# 12.6 AMP PAGE 1

12. FX TRACK PARAMETERS
TIME
AMPLITUDE
Note On
Attack
Decay
Sustain
Note Off
Release
Env.
Delay
12.5 FLTR PAGE 2
On FILTER page 2, you will find the parameters that control the envelope delay parameter. Press [FLTR]
twice to access this parameter page.
12.5.1 DEL
Envelope delay sets the time before the attack phase of the filter envelope starts. This parameter is part
of the filter envelope that controls the multimode filter. You can also press and hold [FUNC] and then
turn DATA ENTRY knob A to quickly access this parameter from FILTER page 1.
12.5.2 FENR
FIlter envelope reset sets the filter envelope behavior:
ON resets the envelopes for each consecutive trig.
OFF does not reset the envelopes for each consecutive trig.
12.5.2 FPAN
Filter Pan adjusts the cutoff frequency of the filter and pans its behavior between the Left and Right
channel. At a value of 0 there is no frequency panning effect. Lower values increase the cutoff frequency
in the Left channel and decrease it in the Right channel. Higher values increase the cutoff frequency in
the Right channel and decrease it in the Left channel.
12.6 AMP PAGE 1
The AMP page 1 controls parameters for the inverted amplitude envelope, effects sends, panning and
volume.
Press [AMP] to access this parameter page.
12.6.1 ATK
Attack Time sets the length of the attack phase of the amp envelope.

12. FX TRACK PARAMETERS
12.6.2 HOLD
Hold Time sets the length of the hold phase of the amp envelope. Fixed Hold time values (0–126) specify
the length of the hold phase, and the envelope ignores Note Off events such as Trig Length, releasing a
[TRIG] key or a key on an external controller. Setting HOLD to NOTE means the hold phase will be deter­
mined by Note On and Note Off events.
If you set HOLD to NOTE and use an external keyboard to trigger the envelope, then the
sound will be sustained (if DEP is set to less than 127) for as long as you press a key on the
keyboard.
12.6.3 DEC
Decay Time sets the length of the decay phase of the amp envelope.
12.6.4 SUS
Sustain Level sets the sustain level of the amp envelope. This parameter is only available if MODE on
AMP Page 2 is set to ADSR.
12.6.5 REL
Release Time sets the length of the release phase of the amp envelope. This parameter is only available
if MODE on AMP Page 2 is set to ADSR.
12.6.6 DEP
Depth sets the amount of modulation from the amplitude envelope. This parameter is only available if
MODE on AMP Page 2 is set to AHD.
12.6.7 DEL
Delay Send sets the amount of the sound from the FX track that is sent through to the Delay effect. For
more information, please see “13.2 DELAY” on page 68.
12.6.8 REV
Reverb Send sets the amount of the sound from the FX track that is sent through to the Reverb effect.
For more information, please see “13.3 REVERB” on page 69.
12.6.9 PAN
Pan positions the sound in the stereo field. The knob function is bipolar with 0 being the balanced mid­
point, L64 sends all sound to the left channel and R63 sends all sound to the right.
12.6.10 VOL
Volume sets the volume of the FX track amplifier. Unlike the track LEVEL, this parameter can be parame­
ter locked.
To prevent an audio feedback loop, the DEL and REV parameters are disabled when the
delay and reverb respectively are routed in to the Analog FX. For more information, please
see “5.4.1 ANALOG FX BLOCK ROUTING” on page 18.
Inverted amplitude envelope with a fixed HOLD time.
TIME
AMPLITUDE
Note On
Attack
Decay
Hold
Note Off
Attack
Decay
Hold
Note On
Note Off
Attack
Decay
Hold
Note On Note Off

12. FX TRACK PARAMETERS
Inverted amplitude envelope with HOLD set to NOTE.
TIME
AMPLITUDE
Note On
Attack
Decay
Hold
Note
Off
Attack
Decay
Hold
Note
On
Note Off
Attack/
Hold
Decay
Note On
Note Off
12.7 AMP PAGE 2
The AMP page 2 controls parameters for the amp envelope reset and the envelope mode.
Press [AMP] to access this parameter page.
12.7.1 AENR
Amp envelope reset sets the amp envelope behavior:
ON resets the envelopes for each consecutive trig (default).
OFF does not reset the envelopes for each consecutive trig.
12.7.2 MODE
Envelope mode sets the amplitude envelope to function as an inverted AHD, an AHD or an ADSR enve­
lope.
12.8 LFO PAGE 1
The Low-Frequency Oscillator can be used to modulate the parameters found on the audio tracks SYN,
FILTER and AMP pages. Customize the low-frequency oscillator behavior, orientation, and depth on this
page. This page controls the behavior of LFO 1
Press [LFO] to access this parameter page.
12.8.1 SPD
Speed sets the speed of the LFO. Try settings of 8, 16 or 32 to sync the LFO to straight beats. The knob
is bipolar. The LFO cycle can be played backward by using negative values.

章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。