← 検索に戻る

11.6 FLTR PAGE 2

11. TRACK PARAMETERS > 11.6 FLTR PAGE 2 · PDF p. 55–56 · OS 1.15A

# 11.6 FLTR PAGE 2

11. TRACK PARAMETERS
PTIM
Portamento Time sets the time for the portamento.
PORT
Portamento turns the portamento on/off. Please note that this parameter is only available on audio
tracks.
For more information, please see “9.8.2 TRACK” on page 38.
11.4 SRC PAGE
The parameters on the SOURCE pages control the playback of the samples, and these parameters vary de­
pending on what machine is selected. The SRC machines are sound engines that uses a particular subset
of the functionality of the sample playback engine. In this section you also find the MIDI machine that lets
you control external, MIDI equipped, gear. You can assign any SRC machine to any track. SRC page 2 con­
tains the same parameters as on page 1 but with a graphical representation of the parameters and a view of
the sample waveform. For more information, please see “A.2 SRC MACHINES” on page 93.
Use the DATA ENTRY knobs to change the settings.
Press [SRC] to access this parameter page.
11.5 FLTR PAGE 1
The parameters on the FLTR page 1 control the filter/EQ, and these parameters vary depending on what
machine is selected The FLTR machines are a collection of different filters and EQ. For more information,
please see “A.3 FLTR MACHINES” on page 104.
Use the DATA ENTRY knobs to change the settings.
Press [FLTR] to access this parameter page.
11.6 FLTR PAGE 2
On FILTER page 2, you will find the parameters that control the base-width filter and the envelope delay
parameter.
The base-width filter is basically a Highpass filter and a Lowpass filter connected in series. The filters BASE
and WIDTH parameters define the base-width filters frequency range.
Examples of how the BASE and WIDTH parameters affect the filter frequency range:
FREQUENCY
AMPLITUDE
Base
Width
FREQUENCY
AMPLITUDE
Base
Width
FREQUENCY
AMPLITUDE
Base
Width

•	 With BASE set to 0, the filter functions as a low pass filter with WIDTH adjusting the fre­
quency range.
•	 With WIDTH set to 127, the filter functions as a high pass filter with BASE adjusting the
frequency range.
•	 With BASE set to 0 and WIDTH set to 127 the filter does not affect the sound.

11. TRACK PARAMETERS
DEL
Envelope delay sets the time before the attack phase of the filter envelope starts. This parameter is part
of the filter envelope that controls the multimode filter. You can also press and hold [FUNC] and then
turn DATA ENTRY knob A to quickly access this parameter from FILTER page 1.
KEY.T
Keytrack sets how much the filter cutoff frequency is affected by what note is playing. The higher the
KEY.T setting, the more the filter opens up at higher notes.
BASE
Sets the base frequency of the filter.
WIDTH
Sets the frequency width above the base frequency.
BW.RT
BW Routing selects if the base-width filter should be routed before (Pre) or after (Post) the machine
selectable filter in the audio path.
RSET
Filter Envelope reset sets the filter envelope behavior:
ON resets the envelope for each consecutive trig (default).
OFF does not reset the envelopes for each consecutive trig.
11.7 AMP PAGE
The AMP page controls parameters for the amplitude envelope, panning, and volume.
Press [AMP] to access this parameter page.
ATK
Attack Time sets the length of the attack phase of the amp envelope.
HOLD
Hold Time sets the length of the hold phase of the amp envelope. Fixed Hold time values (0–126) specify
the length of the hold phase, and the envelope ignores Note Off events such as Trig Length, releasing a
[TRIG] key or a key on an external controller. Setting HOLD to NOTE means the hold phase will be deter­
mined by Note On and Note Off events. This parameter is only available if MODE on is set to AHD.
If you set HOLD to NOTE and use an external keyboard to trigger the envelope, then the
sound will be sustained (if DEC is set to less than 127) for as long as you press a key on the
keyboard.
DEC
Decay Time sets the length of the decay phase of the amp envelope.
SUS
Sustain Level sets the sustain level of the amp envelope. This parameter is only available if MODE on is
set to ADSR.
REL
Release Time sets the length of the release phase of the amp envelope. This parameter is only available
if MODE is set to ADSR.

チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。