11.11 MOD PAGE 3

11. TRACK PARAMETERS > 11.11 MOD PAGE 3 · PDF p. 59–61 · OS 1.15A

# 11.11 MOD PAGE 3

11. TRACK PARAMETERS
DEST
Destination selects the modulation destination for the LFO. Preview how the LFO modulation will affect
the sound by highlighting a destination. Press [YES] to confirm the selection. Press [FUNC] and then
turn the knob to snap to destination sections. For more information, please see “APPENDIX C: MODULA
TION DESTINATIONS” on page 114.
WAVE
Waveform sets the LFO waveform. The Triangle, Sine, Square, Sawtooth, and Random waveforms are
bipolar. The Exponential and Ramp are unipolar.
SPH
Start Phase sets the point within the wave cycle where the LFO will start when it is trigged. 0 makes the
LFO start at the beginning of a complete wave cycle, 64 makes it start at the center. A small square at
the start of the waveform shows that the wave cycle starts at a zero-crossing. If WAVE is set to RND
then the SPH parameter changes to SLEW and adds slew to the transitions in the waveform.
MODE
Trig Mode sets how the LFO will act when a note is trigged.
• FRE is the default free-running mode. It makes the LFO run continuously, never restarting or
stopping even if notes are trigged..
• TRG makes the LFO restart when a note is trigged.
• HLD makes the LFO run free in the background, but when a note is trigged the LFO output level is
latched and held still until the next note is trigged.
• ONE The LFO starts when a note is trigged, then runs to the end of the waveform and then stops.
This makes the LFO function similar to an envelope.
• HLF The LFO starts when a note is trigged, then runs to the middle of the waveform and then stops.
DEP
Depth sets the depth and polarity of the LFO modulation. Both negative (inverted) and positive modula
tion depth is possible. A center setting, 0.00, equals no modulation depth.
11.10 MOD PAGE 2
MOD page 2 page contains the same parameters as LFO page 1, but controls the behavior of LFO 2.
11.11 MOD PAGE 3
MOD page 3 page contains the same parameters as LFO page 1, but controls the behavior of LFO 3.
Please note that MIDI tracks only have two LFOs.

11. TRACK PARAMETERS
LFO WAVEFORMS AND TRIG MODES
TRIG
HALF
TRIG
ONE
TRIG
TRIG
HOLD
TRIG
TRIG
TRIG
TRIG
FREE
TRI
SINE
SQR
SAW
EXPO
RAMP
RAND
LFO TRIG MODE
WAVEFORM
LFO SPEED SETTINGS
The table below shows the LFO speed measured in sequencer steps using different combinations of SPD
and MULT (set to a BPM value) settings. For example, a value of 8 in the table means that the LFO will do
one full cycle in the time it takes the sequencer to advance eight steps.
MULT
S
P
D
1K
2K
2048
1024
1024
1/2
1/2
1/4
1/2
1/4
1/8
1/2
1/4
1/8
1/16
1/2
1/4
1/8
1/16
1/32
1/2
1/4
1/8
1/16
1/32
1/64

12. FX AND MIXER PARAMETERS
12. FX AND MIXER PARAMETERS
The Digitakt II effects and mixers parameters are explained in this chapter.
12.1 EDITING THE SEND FX AND MIXER PARAMETERS
The Digitakt II’s Chorus, Delay and Reverb are send effects and are set on a pattern level. It means that all
the presets in a pattern shares the same effect settings but have individual send levels to the effects. The
Delay, Reverb, and Chorus parameters are set on their respective PARAMETER page, but their incoming
signals are set by the DEL, REV, and CHO send parameters on the FX page of each audio track.
Press [FUNC] + [FX] to access the SEND FX parameter pages, and then use the [UP]/[DOWN] keys to
navigate between the sub pages. Use the DATA ENTRY knobs A-H to change the parameters.
Press [FUNC] + [MOD] to access the MIXER parameter pages, and then use the [UP]/[DOWN] keys to
navigate between the sub pages. Use the DATA ENTRY knobs A-H to change the parameters.
The FX and MIXER parameter settings are stored as part of the pattern. Don’t forget to save
the pattern and give it a unique name once you have achieved the results you want.
12.2 DELAY
(SEND FX PAGE 1)
The Delay send effect takes the input signal, delays it in time and then rejoins it with the original signal.
TIME
Delay Time sets the delay time. It is relative to the current BPM and is measured in 128th notes.
TIME setting
Divide ratio
1/128
1/64
2.67
1/48 (1/32T)
1/64.
1/32
5.33
1/24 (1/16T)
1/32.
1/16
10.67
1/12 (1/8T)
1/16.
1/8
21.33
1/6 (1/4T)
1/8.
1/4
42.67
1/3 (1/2T)
1/4.
1/2
1/2.

チャンクは隣接セクションとページを共有します。見出し前後のテキストは隣のセクションのものです。