10.10 PERFORM KIT MODE
10. THE SEQUENCER > 10.10 PERFORM KIT MODE · PDF 第 52–53 · OS 1.15A
# 10.10 PERFORM KIT MODE 10. THE SEQUENCER The songs are automatically saved as they are created and edited. However, you must save the project if you wish to keep the songs before switching to another project. 10.10 PERFORM KIT MODE In PERFORM KIT mode, any changes made to the preset parameters are not auto-saved, and kits are not loaded when you change the pattern; instead, you keep the previous (tweaked) kit. It means you can keep your parameter tweaks over several patterns and have a smooth evolving performance without having the kits reloaded or inadvertently saving your kit when you change patterns. Press [FUNC] + [PRESET/KIT] to toggle PERFORM KIT mode on/off. When PERFORM KIT mode is on, a flashing “P” is shown next to the pattern name on the screen and the [PRESET/KIT] key is lit orange. 10.10.1 PERFORM KIT MODE ACTIONS • Press [PRESET/KIT] + [NO] to reload the current patterns kit instantly. • Press [PRESET/KIT] + [YES] to save the current patterns modified kit. This will open the SAVE (KIT) menu. For more information please see “9.3.6 SAVE (KIT)” on page 34. Pattern Temp save and Temp reload still works while in PERFORM KIT mode Actions done in PERFORM KIT mode are not automatically saved and will not remain when switch the device off. If you want to keep any changes done to the patten permanently, the pattern must be saved 11. TRACK PARAMETERS 11. TRACK PARAMETERS Here follows a description of all of the parameters that are available on the audio tracks PARAMETER pages. The parameters on the TRIG page are not saved together with the preset, but are instead saved with the pattern. The track parameters may be locked to other settings on any step of the pattern by first pressing and holding a [TRIG] key, then changing the parameters’ settings with the DATA ENTRY knobs. For more information, please see “10.8.1 PARAMETER LOCKS” on page 47. Please note that MIDI tracks has a different set of parameters on the TRIG, SRC, FLTR, and AMP page. For more information, please see “A.2.7 MIDI” on page 101. 11.1 EDITING THE TRACK PARAMETERS There are six PARAMETER pages for the tracks. Press the [PARAMETER] keys to access the tracks PA RAMETER pages. Use the [UP]/[DOWN] keys to cycle through the parameter group’s pages. You can also press a [PARAMETER] key repeatedly to cycle trough the parameter pages in that group. Press and hold a [PARAMETER] key to see the values for all parameters on that page. • You can always reload a preset from its last saved state. Press [TRK] + [TRIG 1–16] + [NO] to reload the preset. • You can also randomize the parameter settings on a specific PARAMETER page on an audio track. Press [PARAMETER] key + [YES] to randomize the relevant parameters on that page. Every time you press this key combination, the parameters randomize in a new way. • Press [PARAMETER] key + [NO] to reset the PARAMETER page to its last saved state. 11.2 TRIG PAGE 1 Here you set the options for notes that are trigged. Here you also select trig conditions. Press [TRIG PA RAMETERS] to access the menu. Change settings using the DATA ENTRY knobs. These general settings affect note trigs placed on the sequencer. Trigs can be locked to other settings on any step of the pattern by first pressing and holding a [TRIG] key, then changing the settings. Press [TRIG PARAMETERS] to access this parameter page. NOTE Trig Note sets the pitch of the note when trigged. When in LIVE RECORDING mode and playing in KEY BOARD mode, the pitch of the [TRIG] keys played will override this setting. Press and turn DATA ENTRY knob A to select only note values that exist in the scale set by KB SCALE. This behavior can be changed using the NOTE PARAM setting in the PERSONALIZE menu. For more information, please see “14.7.6 NOTE PARAM” on page 82 and “8.5.2 KEYBOARD SETUP MENU” on page 25. VEL Trig Velocity sets the velocity of the sequencer’s note trigs. LEN Trig Length sets the length of the note trig. In LIVE RECORDING mode, the duration of pressing the [TRIG] keys overrides this general setting. PROB Trig Probability sets the probability that the trigs on the track plays or not. The probability outcome is re-evaluated every time a trig is set to play. The default setting is 100%, i.e. all the trigs on the track plays every time. This parameter can be parameter locked which enables separate trigs their own probability. LFO.T LFO Trig controls if the LFO will be trigged or not.
章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。