14.4 MIDI CONFIG
14. SETTINGS MENU > 14.4 MIDI CONFIG · PDF 第 77–79 · OS 1.15A
# 14.4 MIDI CONFIG 14. SETTINGS MENU • SEQUENCE DATA Saves the active pattern’s sequence data to the +Drive. A prompt appears when you select this option. Press [YES] to save, or [NO] to cancel the operation. 14.3.4 RELOAD FROM PROJ You must have saved the pattern at least once before you can reload pattern information. • WHOLE PATTERN Reloads the active pattern’s sequence data and kit from the +Drive. A prompt will appear when you select this option. Press [YES] to reload, or [NO] to cancel the operation. • KIT DATA Reloads the active pattern’s kit from the +Drive. A prompt appears when you select this option. Press [YES] to reload, or [NO] to cancel the operation. • SEQUENCE DATA Reloads the active pattern’s all sequence data from the +Drive. A prompt appears when you select this option. Press [YES] to reload, or [NO] to cancel the operation. 14.4 MIDI CONFIG In this menu, various sub-menus dealing with the MIDI functionality of Digitakt II are found. 14.4.1 SYNC Controls how Digitakt II receives and sends MIDI clock and transport commands. Change settings by using the [LEFT]/[RIGHT] arrow keys or the [YES] key. CLOCK RECEIVE sets whether or not Digitakt II responds to MIDI clock sent from external devices. CLOCK SEND sets whether or not Digitakt II transmits MIDI clock. TRANSPORT RECEIVE sets whether or not Digitakt II responds to MIDI transport messages sent from external devices. TRANSPORT SEND sets whether or not Digitakt II transmits MIDI transport messages. PRG CH RECEIVE will, when active, make Digitakt II respond to incoming program change messages, which is useful when wanting to select patterns externally. The MIDI channel that will listen to incom ing program change messages is set in the MIDI CHANNELS menu. For more information, please see “14.4.3 CHANNELS” on page 79. PRG CH SEND will, when active, send program change messages when patterns are changed. The MIDI channel that will send program change messages is set in the MIDI CHANNELS menu. For more information, please see “14.4.3 CHANNELS” on page 79. 14.4.2 PORT CONFIG Here you find the MIDI port related settings. Change settings by using the [LEFT]/[RIGHT] arrow keys. 14. SETTINGS MENU TURBO SPEED press [YES] to start the turbo speed negotiation. Speed is chosen automatically. Please note that you must use a MIDI interface that supports the Turbo-MIDI protocol. OUT PORT FUNCTIONALITY selects what type of signal the MIDI OUT port will send. • MIDI makes it possible for the port to send out MIDI data. • DIN 24 will make the port send DIN 24 sync pulses. No MIDI data is transferred over the port when this option is selected. • DIN 48 will make the port send DIN 48 sync pulses. No MIDI data is transferred over the port when this option is selected. THRU PORT FUNCTIONALITY selects what type of signal the MIDI THRU port will send. The settings are the same as for OUT PORT FUNCTIONALITY. INPUT FROM selects the source Digitakt II will receive MIDI data from. • DISABLED will make Digitakt II disregard any incoming MIDI data. • MIDI will make Digitakt II listen only to MIDI data sent to the MIDI IN port. • USB will make Digitakt II listen only to MIDI data sent to the USB port. • MIDI+USB will make Digitakt II listen to MIDI data sent to both the MIDI IN and USB ports. OUTPUT TO selects the destination to which Digitakt II will send MIDI data. • DISABLED will stop Digitakt II from sending out any MIDI data. • MIDI will make Digitakt II send MIDI data to the MIDI OUT port only. • USB will make Digitakt II send MIDI data to the USB port only. • MIDI+USB will make Digitakt II send MIDI data to both the MIDI OUT and USB ports. If MIDI+USB is selected in the OUTPUT TO settings, MIDI data will limit the USB speed. When sending large chunks of data, make sure you only use the USB setting. OUTPUT CH selects whether the DATA ENTRY knobs will send data on the auto channel or the track channel. PARAM OUTPUT selects what type of MIDI messages the DATA ENTRY knobs will send. For information about which CC/NRPN parameters that will be sent, please see “APPENDIX B: MIDI” on page 109. • CC will make the knobs send out CC MIDI messages. • NRPN will make the knobs send out NRPN MIDI messages. ENCODER DEST controls whether the DATA ENTRY and LEVEL/DATA knobs sends MIDI data or not. When set to INT, the knobs only affects the Digitakt II and no MIDI data is sent. When set to INT + EXT, the knobs affects the Digitakt II and also sends MIDI data to external devices. TRIG KEY DEST controls whether the [TRIG] keys sends MIDI data or not. When set to INT, the [TRIG] keys only affects the Digitakt II and no MIDI data is sent. When set to INT + EXT, the [TRIG] keys affects the Digitakt II, and also sends MIDI data to external devices. When set to EXT, the [TRIG] keys do not affect the Digitakt II but MIDI data is sent externally. MUTE DEST controls whether activating/deactivating mutes will send MIDI data or not. When set to INT, mute only affects the Digitakt II and no MIDI data is sent. When set to INT + EXT, mute affects the Digita kt II and also send MIDI data to external devices. When set to EXT, mute sends MIDI data externally, but do not affect the Digitakt II. RECEIVE NOTES will, when active, make it possible to play Digitakt II using an external MIDI keyboard. RECEIVE CC/NRPN will, when active make it possible to control Digitakt II’s parameters from an external MIDI device sending CC/NRPN data. 14. SETTINGS MENU 14.4.3 CHANNELS This menu handles the MIDI channel configuration. TRACK 1–16 selects the dedicated MIDI channel that is used to receive or send (by turning the knobs) parameter data to or from a specific audio track. If configured as OFF, parameter data are neither received nor sent via MIDI. The sequencer data is always sent on the MIDI channel specified by the CHAN parameter on the SRC PARAMETER page. FX CONTROL CH selects the dedicated MIDI channel that is associated with the parameters on the DELAY, REVERB, CHORUS, and COMPRESSOR parameter pages together with the master overdrive, both for input and output. If configured as OFF, parameter data are neither sent nor received via MIDI. AUTO CHANNEL selects the MIDI channel that will give access to the currently active track. If an ex ternal MIDI keyboard connected to Digitakt II sends MIDI data on this channel, the keyboard will con trol the active track. This is useful when for example quickly changing between the active audio tracks to play different presets. The Digitakt II also uses the AUTO channel to record to the MIDI tracks from external MIDI controllers. PROGRAM CHG IN CH selects the MIDI channel that will listen for incoming program change mes sages. An AUTO setting will use the AUTO channel. Enable Digitakt II to respond to program change messages in the MIDI SYNC menu. For more information, please see “14.4.1 SYNC” on page 77. PROGRAM CHG OUT CH selects the MIDI channel that will send program change messages when changing patterns. An AUTO setting will use the AUTO channel. Enable Digitakt II to send program change messages in the MIDI SYNC. For more information, please see “14.4.1 SYNC” on page 77. 14.5 SYSEX DUMP In the SYSEX DUMP menu, project, pattern, and preset data can be sent and received via the MIDI OUT port or the USB port of the Digitakt II. Select a menu option using [UP]/[DOWN] or the TRACK LEVEL knob. Press [YES] to open the highlighted menu selection. When receiving or sending SysEx data, the MIDI ports or the USB port of the Digitakt II should be connect ed to the external sending/receiving device. Please note that Sysex dump only sends and receives project, pattern and preset data. It does NOT send or receive the presets samples. 14.5.1 SYSEX SEND Here projects, patterns, and presets can be sent to an external device.
章节与相邻小节共享 PDF 页面；标题之前/之后的文本属于相邻小节。